Getting Started/Operation
To ensure correct initial operation, please read these operating
instructions and the safety instructions carefully before using the
device.
Always use suitable respiratory protection when working with paints.
Make sure that the place where you are working is sufficiently venti-
lated.
Do not smoke or eat while you are working, or in the direct vicinity of
where you are working.
When using paints that contain flammable solvents, there is a risk of
explosion. Therefore avoid naked flames and sparks.
Avoid spilling paint or other liquids on the compressor. This can neg-
atively influence the electrical safety and may cause a short circuit,
fire, electrical shock or similar hazards.
The compressor turns off automatically when overheated. In such
case, turn it off and let it cool down for about 30 minutes. It can then
be operated again as usual.
Do not use the compressor for longer than one hour without a pause
(danger of overheating!).
Do not touch the compressor during operation or shortly after, since
it can be very hot.
Installation
• Screw the provided pressure reducer with the connection (7) to the air connection
(9) at the tank.
• Turn the pressure reducer in a way the manometer (8) is well visible from your work-
station.
• Connect one side of the air hose (2) to the air connection (3) at the pressure
reducer.
• Connect the other end of the air hose (2) to your airbrush-gun.
• Fasten all connections well in order to make them airtight.
Leakage test
• Plug the mains plug of the compressor into a mains socket.
• Start the compressor using the ON/OFF switch (1) (position O = off, position I = on).
• The compressor now pumps air into the air tank until the shutdown pressure of 4.1
bar is reached. Now the compressor turns off.
• Check all connection and the air hose for leakages, observing any hissing noise.
• Wait several minutes. If the compressor is not turning on again within this period, all
connections are air-tight.
• If this is not the case retighten all screw joints or use sealing tape when assembling
the connections (however, release the pressure!).
Setting of the working pressure
• Switch on the compressor and wait until the compressor has turned off.
• Pull the pressure regulator (6) upwards and set the correct working pressure by
turning.
• This setting is done with impressed trigger of the airbrush-gun.
• The working pressure is indicated on the manometer (8).
• The perfect working pressure depends on the airbrush-gun or the size of the nozzle
and the consistency of the colour used.
• Try to experiment a little in order to find the adequate working pressure.
• Push the pressure regulator (6) back to its home position in order to save the pres-
sure setting.
Spraying operation
• Now use your airbrush-gun.
• When underrunning the activation pressure (2.8bar) in the air tank the compressor
automatically turns on, increasing the pressure in the air tank back to the shutdown
pressure of 4.1 bar.
• Switch off the compressor via on/off switch (1) after finishing the work.
• Discharge the remaining air from the compressor by pressing the trigger of the air-
brush pistol.
• Before starting the compressor, always release any remaining pressure, by pulling
the trigger on the airbrush-gun. The start-up of the compressor might otherwise be
inhibited by too strong a counter-pressure.
Maintenance and Care
Draining of the water separator
• Regularly discharge incidental condensation by pressing the condensation valve (5)
at the pressure reducer.
• Collect the drained liquid with a cloth.
• The valve automatically closes again if you release the valve.
Other
• Never oil or grease the compressor.
• Only clean its exterior with a soft, dry or slightly moistened cloth. Never use aggres-
sive cleaning agents or chemical solutions as the surface of the housing could be
damaged.
Disposal
Please dispose of the product, when it is no longer of use, according to the
current statutory requirements.
Technical Data
Operating voltage ..........................220-240V~/50Hz
Power consumption ......................70W
Air volume......................................16l/min
Maximum pressure ........................5.5bar
Working pressure ..........................0-4.1bar
Switching pressure on or off ..........2.8/4.1bar
Air connection ................................for hose inner diameter 3.2mm (1/8“)
Dimensions ....................................220 x 140 x 220mm
Weight............................................4.1kg
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2009 by Conrad Electronic SE.
