CONSTRUCTA CJE1900X, User Manual

6

476-016C_v01

Fruit/vegetables

Centrifuging speed

Cabbage

II

Fennel

I

Raspberries

I

Carrots

II

Melons

I

Apricots

I

Nectarines

I

Cucumbers

I

Kiwi

I

Tomatoes

I

Celery

II

Grapes

I

Part names

1

 Juice extractor motor

a

 I-0-II switch

b

 TURBO button

c

 skimmer

d

 vacuum cup

e

 supply cord

2

 Bowl

f

 juice spout

3

 Bowl insert

g

 fin

4

 Filter

5

 Lid

6

 Locking bar

7

 Bowl for small fruits

8

 Pusher

9

 Juice collector

10

 Foam separator

11

 Lid of collector

12

 Pulp collector

13

 Brush

14

 Gasket

Preparations for operation  

(disassembling)

Disassemble  the  juice  extractor  before  first 

usage and clean the parts in contact with 

processed product.

1

 Place  the  juice  extractor  near  the  socket  on  the  firm, 

clean and dry surface.

A

B

2

 Pull down the locking bar 

(6)

 so that the tracks moved 

out of grooves of the lid 

(5)

 from position 

1 

to position

 2

.

3

 Take the pusher 

(8)

 out and remove the bowl 

(7)

 and 

lid 

(5)

.

4

 Then remove the bowl 

(2)

 including the insert 

(3)

 and 

filter 

(4)

.

5

 Then, disassemble the insert 

(3)

 from the bowl 

(2)

.

6

 Finally, remove the gasket 

(14)

 from the bowl 

(2)

, 

as washing the bowl 

(2)

 with the gasket 

(14)

 on is not 

recommended, but only after disassembling it.

 Wash the disassembled parts (apart from the 

motor) carefully in hot water and wash-up 

liquid. You can clean them in dishwasher in 

max temp. 60ºC (apart from the motor and 

filter).  After  drying  carefully  start  assembling 

the clean parts.

Preparations for operation  

(assembling)

1

 Assemble the gasket 

(14)

 into the bowl 

(2)

 making sure 

that the flat surface of the gasket 

(14)

 is facing the top.

2

 Align the bowl 

(2)

 with the gasket 

(14)

 to the motor 

(1)

, 

so that the juice spout 

(f)

 was placed exactly in the casing 

(1) 

groove and 4 buckles from the upper part of the motor 

(1)

 were placed inside the 4 grooves in the bottom of the 

bowl 

(2)

.

3

 Align the insert 

(3)

 to the bowl 

(2)

 so that the fin 

(g)

 of the 

insert 

(3)

 is placed in the cutting of the bowl 

(2)

 over the juice 

spout.

4

 Put the filter 

(4)

 inside and check if it is well mounted and 

rotates easily.

5

 Put the lid 

(5)

  so  that  the  fin 

(g)

 of the insert 

(3)

 was 

placed in the cutting of the lid 

(5)

.

6

 We call your attention to proper assembling. The fin 

(g)

of the insert 

(3)

 should be in the same line as the cutting on 

the bowl 

(2)

 and the cutting in the lid 

(5)

.

7

 Pull the locking bar 

(6)

 up, so that the rolls moved into 

grooves of the lid 

(5)

 from position 

2

 to position 

1

 (you will 

hear a characteristic clicking sound).

8

 Each time insert a bowl for small fruit 

(7)

 on the feeder 

opening of the cover 

(5)

.

9

 Put the pusher 

(8)

 into the chute so that the V-shaped 

hole was put on the knife inside the chute.

10

 Put the pulp collector 

(12)

 under the lid 

(5)

 in the 

following way: lean the collector and place it under the insert 

(3)

 and lid 

(5)

, then push it towards the motor 

(1)

.

11

 Put the juice collector 

(9)

 so that the juice spout 

(f)

 was 

inside the collector 

(9)

.

C