Continental Fireplaces BCDV2CFN, Installation And Operating Instruction

37

W415-0680 / 04.10.08

FIGURE 119

FIGURE 120

OPTIONAL FAN INSTALLATION

FIGURE 121

FIGURE 122

A

A

B

B

FIGURE 118a

FIGURE 118a

C

C

FIGURE 118b

FIGURE 118b

ELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER 

and must be connected and 

grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 C

ANADIAN

ELECTRICAL

CODE

 in Canada or the ANSI/NFPA 70 

NATIONAL

ELECTRICAL

CODE

 in the United States.

To safely install the fan, turn off the electricity fi rst.

If the fi replace was not previously equipped with a fan:

 Route a grounded 2-wire, 60hz 

power cable to the junction box. At this point, it must be strain relieved and insulated.

The wire harness provided in this kit is a universal harness. When installed, ensure that any 
excess wire is contained, preventing it from making contact with moving or hot objects.

To ease installation of the fan, remove the hinge screen and valve control door (lower louvres) 
from the base of the fi replace.

Position the vibration reducing pad into the clip and onto the threaded stud at the other end, pierc-
ing a hole into the pad. The fan assembly must be able to be positioned entirely onto the pad.  Slide the fan 
assembly past the controls and into the  clip. Secure using the lock washer and nut provided. 
Plug the harness cord into the receptacle.

FIGURE 123

FIGURE 124

GD36 THERMOSTATIC SENSOR CONTROL

This optional kit is meant to be used only in conjunction with the GD65 Fan Kit,  shown 
above, which may be ordered from your Wolf Steel / Authorized dealer. 

With the thermostatic sensor option, the fan, when turned on, becomes thermally activated, 
and will automatically run approximately 15-30 minutes after the fi replace has been lit and 
for approximately 30-45 minutes after the fi replace has been turned off. 

Use of the fan increases the output of 
heat.

Unplug the power cord from the receptacle. 
Connect all wires as shown. 

Attach and secure the sensor assembly bracket to the securing 

stud located next to the receptacle/junction box at the bottom left of the unit 
using the lock washer and wing nut. Ensure that the thermodisc touches the 
fi rebox wall.

Plug the power cord back into the receptacle. 

When installed, ensure that any excess wire is contained, preventing it  from making contact with moving or hot objects.

Tilt the blower onto its side. Slide it past the controls and into the clip 

(C)

. Secure to the threaded stud using the lock washer and wing nut  

provided. Ensure that the blower does not touch the fi replace base 
or the fi rebox.

Attach the connectors from the black and white wires to the thermo-
disc and secure the thermodisc bracket to the securing stud at the 
bottom left of the unit using a lock washer and wing nut. Ensure that 
the thermodisc touches the fi rebox wall.  
Attach the connectors from the black and red wires to the blower. 
Attach and secure the variable speed switch using the nut provided. 
Plug the harness cord into the receptacle. 

NOTE:

 To improve access to the variable speed control, we recommend bending 

the mounting bracket forward by approximately 10°.  

The wire harness provided in 

this kit is a universal harness. When installed, ensure that any excess wire is 
contained, preventing it from making contact with moving or hot objects.

Drywall dust will penetrate into the blower bearings, causing irreparable 
damage. Care must be taken to prevent drywall dust from coming into con-
tact with the blower or its compartment. Any damage resulting from this 
condition is not covered by the warranty policy.