background image

8

Limited Warranty

Loren Cook Company warrants that your Loren Cook fan was manufactured free of defects in materials and workmanship, to the extent stated herein. For a period
of one (1) year after date of shipment, we will replace any parts found to be defective without charge, except for shipping costs which will be paid by you.  This war-
ranty is granted only to the original purchaser placing the fan in service.  This warranty is void if the fan or any part thereof has been altered or modified from its
original design or has been abused, misused, damaged or is in worn condition or if the fan has been used other than for the uses described in the company manual.
This warranty does not cover defects resulting from normal wear and tear.  To make a warranty claim, notify Loren Cook Company, General Offices, 2015 East
Dale Street, Springfield, Missouri 65803-4637, explaining in writing, in detail, your complaint and referring to the specific model and serial numbers of your fan. Upon
receipt by Loren Cook Company of your written complaint, you will be notified, within thirty (30) days of our receipt of your complaint, in writing, as to the manner in
which your claim will be handled. If you are entitled to warranty relief, a warranty adjustment will be completed within sixty (60) business days of the receipt of your
written complaint by Loren Cook Company.  This warranty gives only the original purchaser placing the fan in service specifically the right. You may have other legal
rights which vary from state to state.

Corporate Offices:

2015 E. Dale Street

Springfield, MO 65803 417.869.6474

lorencook.com

VCR IOM - October 2007

Summary of Contents for VCR









Reviews: