background image

 

 

 

Initial Set Up

 

Step by step Guide 
 

Once the Water Witch has been mounted properly, 
TESTING OF THE WATER WITCH is required.  To ensure 
that the sensor and solenoid are working properly, 
please complete the following steps: 
 
Step 1

:  Ensure the pool is filled to the operating water 

level required. 

Step 2

:  Connect the sensor and solenoid plugs to the 

control box ensuring that the plugs are 
connected as indicated on the label on the 
control box (

sensor left

; solenoid right). 

Step 3

:  Turn power and water supplies on.  The ON light 

will automatically come on and begin to flash.  
Depending on what position the sensor is in, will 
determine if the sense light is on and flashing or 
the fill light is on. 

Step 4

:  Holding the sensor upside down, check that the 

ON & SENSE lights are flashing approximately 
every two seconds. 

Step 5

:  Turn the sensor the right way up and the ON 

light will continue to flash and the FILL light will 
come on.  This will turn the water on to fill the 
pool. 

IF THE WATER DOES COME ON, YOU HAVE CORRECTLY 
INSTALLED THE WATER WITCH SYSTEM

.   

 

PLEASE FOLLOW STEPS 6 TO 9 TO 

SET THE SENSOR

.   

Summary of Contents for Water Witch













Reviews: