background image

P12

P13

1

The ignition switch

CONTROL FUNTIONS

2

Multifunction switch

 1)

 Proximity switches

2)

 Starter switch

3)

 Off switch

Location

Function

Turn on high beam

Turn on dipped headlight

When press the starter switch,

engine rotation

When press the off switch,

stop rotating engine

When press this accelerator, 

the vehicle starts to move.

 

Prohibit adjusting it.

3

Accelerator controller

Location                           Functions 

                      Key state

All circuits wre disconnected 

Circuit was connected,engine starter

Pull out

Not pull out

5

The front wheel brake handle  

Front-wheel brake handle in the right 

hands.  To  handle  its  direction  pinch 

Rafah as a front-wheel brake.

rear-wheel  brake  pedal  in  the  right 

pedal.  To  trample  the  pedal  as  a  rear 

brake.

7

The fuel Cover

Note:thefuel  Cover  mouth  ventilation 

can not plug.

6

The rear brake pedal

4

The manner of stage change over 

this  vehicle  used  to  the  manner  of 

auto-clutch

 

hand shifting

D:stands for drive

N:stands for neutral gear

R

stands for reverse  gear

R

N

D

Summary of Contents for ATV-3150DX-2





























Reviews: