background image

Introduction

 

 

CoolWorks’ 

IceProbe Thermoelectric Aquarium Chiller

 

(IPAC-50W) is the ideal cooling solution for small aquariums and 

insulated bait or specimen tanks. Quiet, reliable and efficient, the chiller uses advanced thermoelectric technology to directly 
convert electricity into cooling power. 
 
With its threaded probe, nylon nut, and silicon washer, the IceProbe can be easily bulkheaded through a 1.25” hole into siphon 
overflows, prefilters, sumps, or aquarium walls, or suspended from the top of the aquarium. 
 
In a standard aquarium, a single chiller can cool 10 gallons of water 6ºF to 8ºF below ambient air temperature . Multiple 
Aquarium Chillers can be used to achieve higher temperature differentials. 

 
 
 
 

 

Chillers 

 

10 

20 

40 

6-8 3-4 1-2 

10-12 6-8  3-4 

 

 
Greater temperature differentials can be achieved by insulating the exterior surfaces of the aquarium. For example, a single 
Aquarium Chiller can maintain a temperature differential of over 20ºF in a fully insulated 10 gallon aquarium. 
 

Pre-Installation Preparation

 

 

Before installing this product, please read this entire manual carefully. 
 
Assess the area where you intend to bulkhead the IceProbe before drilling any holes.  It is important to ensure there is adequate 
clearance for the probe and ample space for air circulation around the fins and fan. In larger aquariums (20 to 55 gallons), two or 
more Aquarium Chillers may be needed to achieve the desired temperature differential. If you intend to install multiple units in a 
single sump/prefilter/aquarium, space the units so that the heat sinks do not contact each other. 

 

Ventilation

 

 
The IceProbe’s thermoelectric cooling system chills water by removing heat from the water reservoir and dissipating it via the 
system’s fan into the surrounding area. It is critical that the heat can easily escape, as excessive heat build up can adversely affect 
the chiller’s cooling ability. To ensure optimum chiller performance, place the unit in a clean environment with adequate 
ventilation. 

There should always be four to six inches of open space around the chiller. Do not place the chiller in a 

completely enclosed cabinet. 

Without proper ventilation, the cooling system will not function properly and could be 

permanently disabled by the system’s built in safety feature. 

Typical Temperature Pulldown (ºF)

Gallons of Water 

 

Summary of Contents for IceProbe IPAC-50W









Reviews: