4th
3rd
1st
6in
4in
TO PRUNE BRANCHES FROM A TREE
Do not cut any branch larger than 19cm thick. This item is not designed to fell
large trees, it is for pruning. Cut lower branches first and work up the trunk.
Prune heavy branches in several sections to reduce the weight of the branch and
strain on the saw. To avoid tearing the bark, perform a cut on the underside of
the branch and then cut the top. The optimum angle is 60º but this can be
adjusted to suit your requirement.Do not over reach and hold the body of the
machine above shoulder height as this is not a stable position (the pole and
cutter will of course be above shoulder height). When using the pruner, be aware
of overhead wires, power lines, etc. that may over hang your operating area.
Trimming a tree (pruning) is the process of cutting limbs from a living tree.
Make sure your footing is firm. Keep feet apart. Divide your weight evenly on
both feet.
Follow directions below to trim a tree.
Make first cut six inches from tree trunk on underside of limb. Use top of guide
bar to make this cut.
Cut 1/3 through diameter of limb. See diagram above.
Move the Pole Saw four inches further out on limb. Make second cut from above
limb.
Continue cut until you cut limb off.
Make third cut as close to tree trunk as possible on underside of limb stub. Use
top of guide bar to make this cut. Cut 1/3 through diameter of stub.
Make fourth cut directly above third cut. Cut down to meet third cut. This will
remove limb stub.
KICKBACK SAFETY PRECAUTIONS FOR CHAINSAW USERS
WARNING
Kickback may occur when the nose or tip of the guide bar touches an object,
or when the wood closes in and pinches the saw chain in the cut. Tip contact
in some cases may cause a lightning fast reverse reaction, kicking the guide
bar up and back towards the operator. Pinching the saw chain along the top
of the guide bar may push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to Iose control of the chainsaw,
which could result in serious personal injury.
As a chainsaw user you should take several steps to keep cutting jobs free from
accident or injury.
(1) With a basic understanding of kickback you can reduce or eliminate the
element of surprise. Sudden surprise contributes to accidents.
(2) Use a firm grip with thumbs and fingers encircling the handle. A firm grip will
help you reduce kickback and maintain control of the saw.
(3) Make certain that the area in which you are cutting is free from obstructions.
Do not let the nose of the guide bar make contact with a log, branch, or any
other obstruction which could be hit while you are operating the saw.
!
(4) Cut at high engine speeds.
(5) Do not overreach .
(6) Follow the manufacturer’s sharpening and maintenance instructions for the
saw chain.
(7) Only use replacement bars and chains specified by the manufacturer or the
equivalent.
AVOIDING PULL-IN
Pull-in can occur when the bottom of the chain is used for cutting and is stopped
suddenly by hitting a foreign object or getting pinched. This pulls the chainsaw
forwards and may cause the user to lose control. Pull-in can also occur when the
chain is not running at full speed when contact is made with the wood.
• Ensure the chain is rotating at full speed and is correctly positioned when
making a cut.
AVOIDING PUSH-BACK
Push-back can occur when the top of the chain is used for cutting and is stopped
suddenly by hitting a foreign object or getting pinched. This pulls the chainsaw
towards the user and may cause the user to lose control.
• Take care not to twist the chainsaw as it is removed when bucking from
underneath the log.
•
Do NOT
cut more than one log at any one time.
• Be aware of situations that may cause the chain to pinch or pull.
WARNING
It is recommended to first practice sawing easy logs. This
also helps you get accustomed to your unit. Always follow
the safety regulations. The chainsaw must only be used for
cutting wood. It is not suitable for cutting any other type
of material. Vibrations and kickback vary with different
types of woods. Do not use the chainsaw as a lever for
lifting, moving or splitting objects. It is not necessary to
force the saw into the cut. Apply only light pressure while
running the engine at full throttle. When the saw chain is
caught in the cut, do not attempt to pull it out by force,
but use a wedge or a lever to open the way. Do not fit any
other tools to the chainsaw or use for any other purpose
other than those specified in these instructions.
If a blockage occurs, swith off the chainsaw immediately
and remove the obstruction. Be aware the chainsaw could
block and start moving again before you have cleared the
obstruction. Never attempt to unblock while switched on.
be aware that if the blockage occurs, the machine could
cause you to lose balance. Always ensure you have a firm
foothold.
!
OPERATION
