Coram Showers OPTIMA Manual Download | Manualshive

Page: 16 / 16

background image

CORAM SHOWERS LTD

Stanmore Industrial Estate, Bridgnorth, Shropshire WV15 5HP, UK • Tel: 01746 766466 • Fax: 01746 764140 • www.coram.co.uk

Recycling

Packaging

:- The cardboard and polythene parts of this packaging can be recycled.

End of life

:- This product contains materials such as aluminium and glass which can be recycled.

Please contact your local authority to find your nearest recycling centre.

IMPORTANT:

You must not use the shower for 24 hours after installation of the enclosure.

DO NOT

use bleach, scouring powders, solvents or other aggressive cleaning agents. To clean, use warm soapy water and a

clean cloth and rinse off.

Please note: There has been a glass coating applied to this product, use a squeegee to remove water and debris.

Periodically check all fixings and tighten if necessary.

«
...
14
15
16

Summary of Contents for OPTIMA

















Reviews:

No comments

Related manuals for OPTIMA

Brand: Geberit Pages: 28

M7117-H240 73817000

Brand: Hans Grohe Pages: 40

SUPERNOVA SDOP Series

Brand: RAVAK Pages: 16

Croma 100 1jet EcoSmart/Unica'C Set 27742000

Brand: Hans Grohe Pages: 36

AquaClean 8000plus

Brand: Geberit Pages: 4

LELAND 16955-SD-DST

Brand: Delta Pages: 12

Brand: Invacare Pages: 16

Pulsify Planet Edition 105 3jet Relaxation EcoSmart+...

Brand: Hans Grohe Pages: 6

Locarno 04839 1 Series

Brand: Hans Grohe Pages: 12

Xelu Q 400 54127 Series

Brand: Hans Grohe Pages: 16

Talis S 140 72113 1 Series

Brand: Hans Grohe Pages: 16

Torrent 3 28781000

Brand: Hans Grohe Pages: 17

Talis E 150 71754 1 Series

Brand: Hans Grohe Pages: 16

Metropol S 15972000

Brand: Hans Grohe Pages: 20

Vernis Blend Vario 04970 0 Series

Brand: Hans Grohe Pages: 20

Raindance S 300 Air 1jet 27493007

Brand: Hans Grohe Pages: 21

Metropol 32528 1 Series

Brand: Hans Grohe Pages: 24

Brand: Hans Grohe Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands