Artiglio Master
operator’s manual
59
EN
APPROVED M/D PROCEDURE FOR UHP
AND RUN FLAT TYRES
For the detailed M/D procedure for UHP and RUN FLAT tyres, please refer to the
instruction manual wrote by WDK (German Association of the Tyre Industry)
INFLATION
WARNING
Inflation is well known to be a dangerous operation. It must be carried out in accor-
dance with the instructions below. Safety goggles with plain lenses and safety footwear
must be worn.
ATTENTION
During this operation, noise levels assessed at 85 dB(A) may occur. We therefore re-
commend that the operator wears ear protectors.
DANGER
Although the machine limits the pressure, it does not provide sufficient protection if
the tyre bursts during inflation.
Failure to comply with the instructions below will make tyre inflation dangerous.
DANGER
NEVER exceed the pressure recommended by the tyre manufacturer. Tyres may burst
if they are inflated beyond these limits or their structures may incur serious damage
not visible at the time. KEEP THE HANDS AND THE WHOLE BODY WELL AWAY FROM
THE TYRE DURING INFLATION. Make sure you are concentrated during this operation
and check the tyre pressure continuously to avoid excess inflation. A bursting tyre can
cause serious injury or even death.
Inflating tubeless
- Make sure that the wheel on which the tyre has been mounted is firmly clamped to the
self-centring turntable using the centring handle 4 fig. 8a. Also make sure that the tool
head 6 fig. 8a and the top and bottom bead breaker units 9-13 fig. 8a are well clear of
the working area, if possible in the rest position.
- Fix a new valve to the rim.
- Connect the Doyfe union of the inflation line 20 fig. 8b to the stem of the valve, after
removing the cap. Inflate the tyre by pressing
Pedal
2 fig. 9c. The tyre expands, bringing
the beads into the position where they create a seal.
- Continue inflating up to the maximum value of 3.5 bar to position the tyre correctly on the
rim. Make sure you are concentrated during this operation and check the tyre pressure
on the
Air pressure display pressure gauge
1 fig. 9a continuously to avoid over-inflating.
Inflation of tubeless tyres requires a higher air flow-rate to allow the beads to pass over
Summary of Contents for Artiglio Master 26 MI
