background image

Warranty/Disclaimer: 

Unless otherwise specified, all products are for research use or general 

laboratory use only.* Not intended for use in diagnostic or therapeutic procedures. Not for use in 
humans. These products are not intended to mitigate the presence of microorganisms on surfaces 
or in the environment, where such organisms can be deleterious to humans or the environment. 
Corning Life Sciences makes no claims regarding the performance of these products for clinical or 
diagnostic applications. *For a listing of US medical devices, regulatory classifications or specific 
information on claims, visit www.corning.com/resources.

Corning’s products are not specifically designed and tested for diagnostic testing. Many Corning 
products, though not specific for diagnostic testing, can be used in the workflow and preparation 
of the test at the customers discretion. Customers may use these products to support their claims. 
We cannot make any claims or statements that our products are approved for diagnostic testing 
either directly or indirectly. The customer is responsible for any testing, validation, and/or regulatory 
submissions that may be required to support the safety and efficacy of their intended application.

For a listing of trademarks, visit www.corning.com/clstrademarks. All other trademarks are the property of their respective owners.  
© 2022 Corning Incorporated. All rights reserved.   9/22   CLS-AN-696DOC REV2 

Corning Incorporated
Life Sciences

www.corning.com/lifesciences

NORTH AMERICA
t 800.492.1110 
t 978.442.2200

ASIA/PACIFIC
Australia/New Zealand
t 61 427286832
Chinese Mainland
t 86 21 3338 4338
India

 

t 91 124 4604000
Japan
t 81 3-3586 1996
Korea
t 82 2-796-9500
Singapore
t 65 6572-9740
Taiwan
t 886 2-2716-0338

EUROPE
CSEurope@corning.com
France
t 0800 916 882
Germany
t 0800 101 1153
The Netherlands

 

t 020 655 79 28
United Kingdom
t 0800 376 8660
All Other European  
Countries
t +31 (0) 206 59 60 51

LATIN AMERICA
grupoLA@corning.com
Brazil
t 55 (11) 3089-7400
Mexico
t (52-81) 8158-8400

Summary of Contents for AXYGEN I-4010
















Reviews: