Side impact protection block cover:
Carefully pull the cover off (k).
IMPORTANT:
The covers are a safety feature.
NEVER
use the
child car seat without them.
23 - refitting the seat cover
Ensure the sponge pad is placed on the seat (a).
Fit the side impact protection block covers by stretching the cover over the impact pads (b).
Place the cover on the seat.
Fit the elastic strap over the headrest (c).
Fit the six elastic loops on the inside of cover to the mounting points on the seat (d). Fit
the cover around the adjuster button (e) then push the harness adjuster strap through
the elastic loop under the harness adjuster flap (f).
Stretch the cover over the seat and backrest (g) ensuring the elastic edging tucks inside
the seat structure and secures the cover to the seat.
24 - refitting the headrest cover
Fit the elastic loop (a) through the slot in the vehicle seat belt lock.
Fit the elastic loop under the vehicle seat belt lock (b).
Close the vehicle seat belt lock (c).
Stretch the cover over the headrest (d) ensuring the elastic edging tucks inside the
headrest structure and secures the cover to the headrest.
25 - refitting the harness for group 1 use - 1
Pull the seat forward to gain access to the rear of the seat. See Step 13.
Release the harness strap (a).
At the front of the child car seat pull the harness adjuster strap out from under the
harness adjuster flap (b).
26 - refitting the harness for group 1 use - 2
Feed the crotch harness through the slot in the seat liner and seat cover (a). Push the
crotch harness clip through the slot in the seat (b). Flatten the clip to secure.
Fit the waist harness clips through the slots in the seat cover and seat (c). Push the clips
through the seat and back up from underneath (d). Flatten the clips to secure. Loosening
the cover around the waist harness mounting points will help with access.
27 - refitting the harness for group 1 use - 3
Feed the shoulder harness through the chest pads then push the straps through the slots
in the upper seat liner and backrest (a).
Slide the chest pad straps onto the chest pad belt locking bar at the rear of the backrest
(b). Push the chest pad locking bar into the backrest until it’s locked in place (c).
Fit the ends of the shoulder harness straps to the harness connector (d) ensuring the
straps are correctly attached.
Close the seat and refit the locking bar.
Summary of Contents for HUG
