background image

 

-16-

User can choose different control mode to start his work out. See below is main description of each control mode. 

3. 

EXECUTE   MANUAL/PROGRAMS/ WATT CONSTANT/PERSONAL/H.R.C 

Execute selected control mode. 

4. RE-SET 

 

TIME/DISTANCE/CALORIES/WATTS/HEART 

RATE 

Setting and inputting user wanted function value of above, the function value of display will count down to zero; or 
user can not inputting these, just forget setting value, computer will know your workout is from 0 to end value. 

5. PRESS 

 

ENTER/UP/DOWN/START/PAUSE 

USE UP / DOWN key to increase / decrease function value. 
After setting each function value to press “ENTER” to confirm your setting 
START / PAUSE- Finish previous setting step to press START to start operating; user can press “PAUSE” if he/her 
want to pause workout a while. 

6. 

TEST   RECOVERY/BODY FAT 

Press RECOVERY or BODY FAT, the computer will calculate your recovery and body fat value on display regarding 
with your user data and actual workout function value.   

FUNCTION DESCRIPTION 

MANUAL     

Set the resistance level using the dot matrix display then (if required) set exercise parameters 
TIME/DISTANCE / CALORIES / PULSE then press START/STOP to START manual program. 

PROGRAM 

12 automatic adjusting programs with control exercise (P1~P12),   

             Resistance level can be adjusted during PROGRAM DIAGRAM is flashing. 
 

 
 
 
 
 

WATTS CONSTANT User can default WATTS value at his/her desire 10-350 watts between 10~350 watts by using the 

UP/ DOWN knob. To fix WATTS constant value and then press ST/STOP key. Use WATTS 
control mode to train yourself in different WATTS’s constant. 

PERSONAL 

Create your own Program profile through U1~U4 by setting the resistance level for each individual 
segment. Then the Program will be automatically saved for future use. U0 ENTER can be set the same 
as U1~U4 but this Program cannot be saved.   

H.R.C 

HEART RATE CONTROL- Select your own target Heart Rate of choose one of the preset programs 55%, 

75%

or 90%. Please enter your age into the User Data to ensure that your target heart rate is set 

correctly. The PULSE display will flash when you have reached your target heart rate according to the 
Program you have chosen.   

i. 

55% -- DIET PROGRAM 

ii. 

75% -- HEALTH PROGRAM 

iii. 

90% -- SPORTS PROGRAM 

iv. 

TARGET—USER SET TARGET HEART RATE 

RECOVERY: 
When you have finished your workout, press RECOVERY. For RECOVERY to function correctly, it needs your Heart Rate 
input. TIME will count down from 1 minute and then your fitness level from F1 to F6 will be displayed.   

NOTE: during RECOVERY, no other displays will operate.     

F 1 ~ F6 = RECOVERY HEART RATE LEVEL     

Operating ENTER: 
1. User press H.R.C key to start the H.R.C. 
2. Get the result from F1 - F6. 

Condition 

Score 

Heart Rate 

Excellent

 

    F1 

Above 50 

Good

 

F2 

40 ~ 49 

Average

 

F3 

30 ~ 39

 

Fair

 

F4 

20 ~ 29

 

Poor

 

F5 

10 ~ 19

 

Very Poor

F6 

Under 10 

Operating Mode: 
1. User press H.R.C key to start the H.R.C testing 
2. Get the result from F1 - F6. 
 
 
 

BODY FAT 

:

 Press the “BODY FAT” key, and hold hand-pulse with both hand 6 seconds. The LCD monitor show 

the user 1-user 4‘s body fat percent.   

Summary of Contents for C1000U-AT























Reviews: