background image

*

This connector is different if used with option -J.Refer to Fig. 5.3 

for pin arrangements.

¡

When external power source is in the range of 4.5 - 12.5V,  cur-

rent limit resistance R is not required.  However,  when external 

power source exceeds 12.5V,  current limit resistance R must be 

connected.

To calculate the current limit resistance, use the following equa-

tion:

R [

W

] = 

Vcc- (1.1+Ri

X

0.005)  

                         0.005

Where ; 

Vcc = External Power Source

Ri = The internal resistance (780

W

)

¡

A wrong connection may damage the internal components of the 

unit.

¡

Remote ON/OFF circuit (RC (+),  RC (-) ) is isolated from input,  

output and FG.

¿

-N1

-

A type with a fi tting supporting a dedicated DIN rail.

-

Consult us external view in details.

-

A type in which terminal block screws are aligned vertically (op-

tion: -T).

¿

-W

 (It is not possible to combine with option -J)

-

-W is available for detecting low input alarm (PF),  detecting low 

output voltage (LV) and operating N+1 redundancy.

-

Alarm specifi cation is shown Table 5.2.

-

Special harness is prepared,  refer to option parts.

-

Consult us external view in details.

-

Each alarm (PF,LV) is isolated from input,  output and FG.

AC-DC Power Supplies Enclosed Type

Instruction Manual

ADA-15

ADA

Fig.5.4 Example of use remote ON/OFF

Fig. 5.5 Din Rail Attachment

Table 5.2  Explanation of alarms

Fig.5.6 PF internal circuit

Fig.5.7 LV internal circuit 

PF+

PF-

LV+

LV-

+V

 -V

R

Ri

Vcc

I=20mA max

SW

CN3*

RC (+)

RC (-)

Connector for remote ON/OFF (Optional)

1

2

External Power
Source

When line voltage is abnor-

mal (low input voltage out of 

range),  the alarm outputs from 

CN3.

If the output voltage drops be-

low the rating, the alarm signal 

is output from CN3.

Note :  

1

This becomes un-

stable in the event 

of output overcur-

rent (intermittent 

overcurrent).

2

The alarm signal is 

not output for paral-

lel operation that 

does not use OR 

diodes.

PF

LV

Open collector method

Good : Low

  

 

(0 - 0.8V,  1mA max)

Fail   : 50V max

Open collector method

Good : Low

  

 

(0 - 0.8V,  1mA max)

Fail   : 50V max

Alarm

Output of alarm

Please consult us details.

me̲ada1.indd   ADA-15

me ada1 indd ADA-15

2015/08/07   9:23:58

2015/08/07 9:23:58

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for ADA1000F












Reviews: