10
5.8.2 - Programming of domestic hot water timing
Using key KM and subsequently key K4 (>>), access is gained to page 2 of the menus.
Using key K1 (PROG), the programming menu is selected.
Once this menu has been selected, it is possible to make one of the following choices:
· RIS (HEATING timer)
· SAN (DOMESTIC HOT WATER timer)
If the choice does not appear, it means that the domestic hot water programme is already active (PROG SAN
parameter as per section 5.9, at 1), or that it is linked to the programming of the heating (PROG SAN parameter
as per section 5.9, at 3).
So as to carry out programming of the domestic hot water independently from the programming of the heating, it
is necessary to set the PROG SAN parameter as per section 5.9, at 2.
- press key K2 (SAN), one accesses the menu for programming the domestic hot water timer (the clock symbol
which appears on the display acts as confirmation that the time programming of the heating is taking place);
- press key K1 (GIO) in order to set the day one intends to programme (by repeatedly pressing it, one will see that
the two letters corresponding to the day of the week change continually, updating the day);
- press key K2 (IMP) in order to access the menu for selecting the on and off timebands for the domestic hot
water service , comprising OFF and ON, plus the choice which makes it possible to leave the value unaltered ( -
- );
- choose the key corresponding to the function one intends to programme (OFF) or (ON), the display automatically
returns to the previous setting;
- using keys K+ e K-, set the timeband, for that day, during which you wish it to operate in the chosen function; (the
OFF and ON timebands are displayed on the histogram bar, respectively by means of: nil, a small black square at
the base of the histogram);
- press key K2 (IMP) once again so as to select the new OFF or ON function timeband and repeat the operation
carried out previously in order to set the new operating timeband.
So as to shift from one part of the timer to another over 24 hours, without changing the setting made previously,
proceed as follows:
- press key K2 (IMP), then press key K1 (- -); the display returns to the clock display, thus move between the
hours using the keys K+ e K- until reaching the desired time;
- repeat the above procedure, selecting a new ON or OFF operating timeband.
Once the programming of the day has been carried out, just press key K3 (COP) in order to copy the same
programming to the next day, then press key K1 (GIO) in order to select the following day (whose time will have the
same programming made above), then press K3 (COP) once again so as to copy the programming to the next
day, and so on for all the days of the week which one wishes to programme as the same as the others. In order to
programme one day of the week differently, it is sufficient to do so as per the above indications, without it being
copied from a previous day.
In order to save the programme set, just press key KM. The display will return to normal view. If the display shows
the histogram bar 11 as per figure 3, it means that the programme set above is already active. If this is not so,
follow the instructions in section 5.2 to activate it.
5.8.3 - Calling up an existing programme for domestic hot water
The remote control makes 2 pre-compiled programmes available, in order to facilitate the user when programming
the time. Proceed as follows to access them:
- press key KM and subsequently key K4 (>>), page 2 of the menus is accessed;
- press key K1 (PROG), the programming menu is selected;
Once this menu has been selected, it is possible to make one of the following choices:
· RIS (HEATING timer)
· SAN (DOMESTIC HOT WATER timer)
If the PROGR SAN parameter set (see section 5.9) does not envisage the management of the SAN timer (different
to 2), one directly accesses the programming of just the timer for the heating, therefore set PROGR SAN at 1 or
3.
- press key K2 (SAN), one accesses the menu for programming the domestic hot water timer;
- press key K4 (PRE), one accesses the menu for selecting the pre-set operating programme;