background image

 

Cee® Apogee™ Developer Manual

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 

4

 of 

15

 

1. 

Apogee™ Developer Introduction 

 

1.1. Confidentiality Statement

 

 

Information supplied is for the use in the operation and/or maintenance of Cee equipment. 
Neither this document nor the information it contains shall be disclosed to others for manufacturing or any 
other purpose without written authorization from, Cost Effective Equipment, LLC. 

 

1.2. Warranty

 

 

Cost Effective Equipment, LLC warrants to the original purchaser (Buyer) that equipment is free from 
defects in material and workmanship under normal use and service in accordance with Cee instructions 
and specifications. Buyer Shall promptly notify Cee of any claim against this warranty, and any item to be 
returned to Cee shall be sent with transportation charges prepaid by Buyer, clearly marked with a Return 
Authorization (RMA) number obtained from Cee Customer Support. Cee’s obligation under this warranty is 
limited to the repair or replacement, at Cee option, of any equipment, component or part which is 
determined by Cee to be defective in material or workmanship. This obligation shall expire one (1) year 
after the initial shipment of the equipment from Cee. 
This warranty shall be void if: 

 

(a) Any failure is due to the misuse, neglect, improper installation of, or accident to the equipment. 
(b) Any major repairs or alterations are made to equipment by anyone other than a duly authorized 
representative of Cee. Representatives of Buyer will be authorized to make repairs to the equipment 
without voiding warranty, on completion of the Cee training program. 
(c) Replacement parts are used other than those made or recommended by Cee.  

 

CEE MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO EQUIPMENT. 
NO WARRANTY IS MADE AS TO THE MERCHANTABILITY OF THE EQUIPMENT NOR ITS FITNESS 
FOR ANY PARTICULAR PURPOSE. In no event shall Cee be liable for consequential loss or damages, 
however caused. No person or representative of Cee is authorized to assume for Cee any liability in 
connection with Equipment nor to make any change to this warranty unless such change or modification is 
put in writing and approved by an authorized representative of Cee in writing. 

 

This warranty shall be governed by the laws of the state of Missouri U.S.A. 

 

1.3. Returned Materials 

 

Any materials, parts, or equipment returned Cost Effective Equipment, LLC must be clearly labeled with a 
Return Material Authorization (RMA) number. 
 
To obtain a RMA number, contact: 

 

Cee Customer Support 
Telephone: (573) 466-4300 
E-Mail: support@costeffectiveequipment.com 
Web Address: http://www.costeffectiveequipment.com 
Shipping information with RMA number: 

 

Attn: Cee Customer Support 
Cost Effective Equipment 
3703 HyPoint Blvd 
Rolla, Missouri 65401

 

 

Summary of Contents for Apogee
















Reviews: