background image

THIS PRODUCT IS DESIGNED FOR RESIDENTIAL USE BY HEALTHY 

INDIVIDUALS

Children should not be allowed to use these products without adult supervision. Pregnant women and those 
with heart conditions or other conditions that limit normal physical activity should consult a doctor before use.

REPAIR PROCEDURES

Most minor scratches (up to 1/64” deep) and cigarette burns can be removed by sanding the area with 
#180 or #240 wet or dry sand paper and progressing down to #600 or #1200 grit. Finally, apply light buffing 
compound and buff area with a clean stitched cotton buffing pad or equivalent. Use an extra application of 
fine buffing compound if necessary.
For Cracks and Major surface damage, call our service line (800) 426-8964.

WHIRLPOOL TROUBLE SHOOTING

MOTOR WILL NOT START:

1. Check Circuit Breakers.
2. Check for incorrect or loose wire connections.
3. Make sure the correct power supply is being used.
4. Electronic On/Off switch should be in the “On” mode.
5. Make sure that the jets are fully opened and water is flowing.

WATER LEAKS:

1.  Check compression fittings (union connectors) making sure they are properly aligned and secured. HAND 

TIGHTEN ONLY. 

DO NOT USE ANY TOOLS

.

2. Make sure the O-ring is properly seated and not damaged.

SAVE THESE INSTRUCTIONS

This product and its components are ETL listed and IAPMO approved

Summary of Contents for the estate 507187











Reviews: