background image

15

A 511 - DTC 628  Eng.

 

 06.12.05 LB

We reserve the right to make changes without notice

19. COMMISSIONING 

Testing to be carried out when installation has been completed and the electrical wiring and confi-

guration carried out and tested.

19.

1

 Testing C-Ring 

 

The C-Ring testing page appears only if  PRIMARY is configured.

Ensure that the controllers connected in C-Ring:

– are correctly powered from the mains at  ( 230 V~).

– one controller only is configured as

– all the other  controllers are Slave or configured as    

– all the controllers are selected on the testing page

DTC 628 sends via C-Ring a signal every 5 seconds.  On all appears.  If the connection if satisfactory 

the word “YES” replaces “??” on all the displays.  If on one or more displays “YES” does not appear 

this means that there is a break between the last controller with “YES” and the first with “??”:

Examples of testing a C-Ring with four controllers:

– Cont.1 "YES"  – Cont..2 "YES" – Cont..3 "YES" – Cont. 4 "YES" : Connection OK

– Cont.1 "??" 

– Cont. 2 "YES" – Cont. 3 "YES" – Cont. 4 "YES" : Break between 4 and 1

– Cont.1 "??" 

– Cont..2 "YES" – Cont. 3 "??"  – Cont. 4 "??"  : Break between 2 and 3

– Cont.1 "??" 

– Cont..2 "??"  – Cont. 3 "??"  – Cont. 4 "??"  : Break between 1 and 2

19.

2

 Testing control ouputs

With + and – keys select:

• Output : - BURNER = On-Off control burner 

• Status  : - OFF; - ON.

• Output : - MODULAT = modulating control burner

• Status  : - IDLE; - LOWER; RAISE.

• Output : - VALVE = On-Off control shut-off valve.

• Status  : - OPEN; - CLOSED.

• Output : - PUMP = On-Off control pump.

• Status  : - ON; - OFF.

Check result of each operation.

19.

3

 Testing detector connections

Each individual detector can be tested by reading the temperature indicated by the controller in the 

“MEASUREMENTS” menu and deciding if the value is reasonable. 

 C R i n g : ? ?

 C R i n g   c o n n e c t i o n

 S E C O N D A R Y

 C R i n g   c o n n e c t i o n

 P R I M A R Y

M6.

4

 C R i n g   c o n n e c t i o n

 S E C O N D A R Y

 C R i n g   c o n n e c t i o n

 P R I M A R Y

M7.

1

 C R i n g : ? ?

 

 O u t p u t : B U R N E R 

 S t a t u s : O F F  

M7.

2

 O u t p u t : M O D U L A T 

 S t a t u s : I D L E

 O u t p u t : V A L V E

 S t a t u s : C L O S E D

 O u t p u t : P O M P A

 S t a t u s : O F F

Summary of Contents for DTC 628





















Reviews: