background image

NOTE:
The value of the voltage set for the “UV Alarm” should be
equal to or higher than the value set for “UVP” or else the
unit will shut-down without any audible warning.

˙

O/P Parameter 

Model

110V
230V

97 VAC ~ 123 VAC

194 VAC ~ 246 VAC

Setting value range

Model

110V
230V

47 Hz ~ 63 Hz
47 Hz ~ 63 Hz

Setting value range

Model

12V
24V
48V

10.5 VDC ~ 11.5 VDC

21 VDC ~ 23 VDC
42 VDC ~ 46 VDC

Setting value range

5. UV Alarm : Setting Under Voltage (UV) alarm. When the input
    voltage is lower than the set value, the SD-series will sound a
    “beep” to remind you that the unit is going to shut-down. In the
    meantime, the contact in the internal Dry Contact Relay will
    open / close.
    Default= 10.5 VDC @ 12 V Model, 21 VDC @ 24 V Model.
                              42 VDC @ 48 V Model

1. O/P Voltage : Setting the SD-series output voltage on the
    inverter operation.  
    Default= 110 VAC @110 V Model, 230 VAC @ 230 V Model

2. O/P Frequency : Setting the SD-series output frequency on the
    inverter operation.
    Default= 60 Hz @ 110 V Model, 50 Hz @ 230 V Model.

3. Sync Frequency : If a generator is distorted. The output
    waveform (too low frequency) is used as AC source, the allowed
    frequency window for the incoming AC power can be enlarged.

9

Summary of Contents for CR-10













Reviews: