Country Flame Bayvue DV 30, Owner'S Manual

OPERATING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING 

WARNING:

 If you do not follow these instructions exactly, a fire or explosion 

                         may result causing property damage, personal injury, or loss of life. 

A. 

The Bayvue DV has a pilot light system that must be lit by hand.  
Follow these instructions exactly, when lighting the pilot. 

B. 

BEFORE LIGHTING the pilot light, it is important to smell all around 
the Bayvue DV for potential gas leaks.  Be sure to smell next to the 
floor because some gas fuel is heavier than air and will settle to the 
lowest point. 
 
WHAT TO DO IF YOU SMELL GAS 

C. 

Use hand pressure to push in or turn the 
ON/PILOT/OFF control knob.  Do not use a 
tool.  If the control knob will not push in or 
turn by hand, do not attempt repair.  Call a 
qualified service technician.  Attempted repair 
may result in fire or explosion. 

•

Do not try to light the Bayvue DV. 

•

Do not touch any electrical switch; do not use any phone in your 
building. 

•

Immediately call your gas supplier from a neighbor’s phone.  
Follow the gas supplier’s instructions. 

•

If you cannot reach your gas supplier, call the fire department. 

D. 

Do not use the Bayvue DV if any part has 
been under water.  Immediately call a 
qualified service technician to inspect the 
Bayvue DV and replace any part of the 
control system and any gas control that has 
been under water. 

LIGHTING INSTRUCTIONS 

1. 

STOP!

  Read the safety information above this section. 

8. 

Push  in  and turn the ON/PILOT/OFF control 
knob counterclockwise to “ON.” 

2. 

3. 

4. 

5. 
6. 
7. 

Turn off all electrical power to the Bayvue DV. 
Open the Bayvue DV bottom panel to expose the gas control panel. 
Push in on the ON/PILOT/OFF control knob slightly and turn 
clockwise to “OFF.” 
Wait five minutes to clear out any gas.  Then smell for gas including 
near the floor.  If you smell gas, STOP!  Follow “B” of the safety 
information above. 
Turn ON/PILOT/OFF control knob counterclockwise to “PILOT.” 
Push in the ON/PILOT/OFF control knob and hold in.  By repeatedly 
pressing the piezoelectric igniter, a pilot flame should appear.  If 
flame goes out repeat steps 5 thru 10.  If flame stays lit, go to Step 10. 

9. 

10. 
11. 

Close the Bayvue DV bottom access panel. 
Turn on electrical power to Bayvue DV. 
The pilot flame should be visible through the 
door glass in the lower right hand corner 
between the front and middle logs.  See the 
picture below for parts description and view 
of normal pilot flame pattern. 

ON

OFF

PILOT

HI

LO

PILOT

ADJ

IN

OUT

TO TURN OFF GAS TO BAYVUE DV

1. 

When servicing the Bayvue DV, turn off electrical power. 

3. 

Push in ON/PILOT/OFF control knob and 
turn clockwise to “OFF.”  Do not force. 

2. 

Open the Bayvue DV bottom access panel  to see control panel. 

4. 

Close the Bayvue DV bottom access panel. 

FIRST FIRE 

Version 1.0h 

46 

Reduce odor by ventilating the room the first few times the unit is operated.  Burn the first two fires no more than 15-
20 minutes.  Allow the Bayvue DV to completely cool between burns.  Burn the third fire 30-40 minutes and allow 
proper cooling time.  Operate the appliance according to the instructions contained in this manual.