background image

3

For additional information email 

info@ardisam.com

 or call 800-345-6007 M-F 8-5

Operator’s Manual 

20969 CRT Tiller

WARNINGS AND SAFETY PRECAUTIONS

Owner’s Responsibility
Accurate assembly and safe and effective use of the machine is 

the owner’s responsibility.

• 

Read and follow all safety instructions.

• 

Carefully follow all assembly instructions.

• 

Maintain the machine according to directions and 

schedule included in this CountyLine® operator’s 

manual.

• 

Ensure that anyone who uses the machine is familiar 

with all controls and safety precautions.

Special Messages
Your manual contains special messages to bring attention to 

potential safety concerns, machine damage as well as helpful 

operating and servicing information. Please read all the 

information carefully to avoid injury and machine damage.

NOTE: General information is given throughout the 

manual that may help the operator in the 

operation or service of the machine.

 

THIS SYMBOL POINTS OUT IMPORTANT 

SAFETY INSTRUCTIONS WHICH IF NOT 

FOLLOWED COULD ENDANGER YOUR 

PERSONAL SAFETY. READ AND FOLLOW ALL 

INSTRUCTIONS IN THIS MANUAL BEFORE 

ATTEMPTING TO OPERATE THIS EQUIPMENT.

Before Operating Equipment:

Please read this section carefully. Read entire operating and 

maintenance instructions for this product.  Failure to follow 

instructions could result in serious injury or death.   Operate 

the machine according to the safety instructions outlined 

here and inserted throughout the text.  Anyone who uses this 

machine must read the instructions and be familiar with the 

controls.
Intended Use / Foreseeable Misuse

IMPORTANT:  This is a motorized rotary cultivator that works 

the soil by means of rotating tines.  It is pedestrian-controlled, 

but not self-propelled, with a gasoline-fueled internal 

combustion engine to power the tines.  It shall not be used for 

any other purpose.

 

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT 

AVOIDED, COULD RESULT IN DEATH OR SERIOUS 

INJURY AND/OR PROPERTY DAMAGE.

 CAUTION

CAUTION INDICATES YOUR EQUIPMENT CAN BE 

DAMAGED IF THE SAFETY INSTRUCTIONS THAT 

FOLLOW THIS SIGNAL WORD ARE NOT OBEYED.

 

WARNING

CALIFORNIA PROPOSITION 65 WARNING
ENGINE EXHAUST FROM THIS PRODUCT 

CONTAINS CHEMICALS KNOWN TO THE STATE OF 

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, 

OR OTHER REPRODUCTIVE HARM.

 IMPORTANT

INDICATES HELPFUL INFORMATION FOR PROPER 

ASSEMBLY, OPERATION, OR MAINTENANCE OF 

YOUR EQUIPMENT.

 WARNING

YOU MUST READ, UNDERSTAND AND COMPLY 

WITH ALL SAFETY AND OPERATING INSTRUCTIONS 

IN THIS MANUAL BEFORE ATTEMPTING TO SETUP 

AND OPERATE YOUR MACHINE.
FAILURE TO COMPLY WITH ALL SAFETY AND 

OPERATING INSTRUCTIONS CAN RESULT IN LOSS 

OF MACHINE CONTROL, SERIOUS PERSONAL 

INJURY TO YOU AND/OR BYSTANDERS, AND RISK 

OF EQUIPMENT AND PROPERTY DAMAGE. THE 

TRIANGLE IN THE TEXT SIGNIFIES IMPORTANT 

CAUTIONS OR WARNINGS WHICH MUST BE 

FOLLOWED.

 

DANGER

SRT

CRT

Summary of Contents for 20969

































Reviews: