background image

WARRANTY

LIMITED WARRANTY

Important Notice to Consumer:

Coustic offers the following warranty to the

ORIGINAL PURCHASER of COUSTIC products within the period stated herein:

Coustic warrants the XM2, XM4 and XM6 against defects in material and

workmanship for a period of ONE (1) YEAR from date of original purchase.

The limited warranty is offered as an Over The Counter (OTC) exchange 

providing that the product was purchased from an authorized Coustic dealer

and is accompanied by valid sales receipt at the time of exchange.

Replacement units will be warranted for the remaining portion of the original

warranty period.

IMPORTANT:

THIS WARRANTY DOES NOT COVER INSTALLATION OR 

DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE, IMPROPER

WIRING, INCORRECT VOLTAGE, OPERATING UNIT AGAINST 

INSTRUCTIONS IN OWNER’S MANUAL OR ANY PRODUCT WHICH 

HAS BEEN OPENED, TAMPERED WITH OR SERIAL NUMBERS REMOVED.

This warranty does not cover labor costs for removal and/or installation of

the unit for repair. Under no circumstances shall Coustic be liable for any

special, incidental or consequential damages or for any other expenses

incurred by reason of use or implied including any implied warranty of 

merchantability or fitness for particular use or otherwise. 

This warranty gives the CONSUMER specific legal rights and he may also

have other rights which vary from state to state. Some states do not follow

the exclusion or limitation of incidental or consequential damages, hence the

above exclusions and limitations may not apply.

For additional information, call us at 602-438-2020, or visit our website at

www.coustic.com.

WWW.COUSTIC.COM

25

TROUBLESHOOTING GUIDE

SYMPTOM – No Power

PROBABLE CAUSE – Check all the ground, B+ and remote terminals 

for tight connection. 

• Check all fuses.

• Use a Volt/Ohm meter to check all power wire connections to see 

if the system is rec12VDC.

SYMPTOM – “Motorboating”: The power indicator going off repeatedly

when the audio system is on.

PROBABLE CAUSE – Check if the crossover power wire is connected

directly to the battery.

• Check the battery voltage; if low, recharge or replace it.

• Check if the crossover has good ground connection (i.e. whether the

ground wire is making good contact with a bare metal spot of the

vehicle chassis).

SYMPTOM – When the engine is running, the audio system has a whining

noise that remains unchanged or disappears with the increase of audio volume.

PROBABLE CAUSE – Check all the power wires to see if they are all 

connected directly to the battery.

• Check all the ground connections to the entire system for good contact

with bare metal of the vehicle chassis. Check if the source unit and the

crossover are grounded at the same reference point.

SYMPTOM – Obvious distortion at low volume.

PROBABLE CAUSE – Output level of various channels not compatible,

refer to section titled OUTPUT LEVEL ADJUSTMENT.

SYMPTOM – Overal sound effect good, but bass abnormal (more bass at the

two extreme settings of the balance control thatn at the center setting.

PROBABLE CAUSE – The subwoofers are “outof phase” with each other,

thus canceling the bass when the balance control is at the center posi-

tion. Check the wiring form the amplifier to the subwoofers (positive “+”

to positive “+” and negative ”-” to negative “-”.

Summary of Contents for XM6
















Reviews: