background image

 

Notice:  

* The battery is not fully charged in the factory, and please charge the new battery when you use 

the radio for the first time.   

* The radio is supplied with a CB-01/02 battery manufactured by COVALUE company. 

* When you charge the battery for the first time after purchasing or long storage (over 2 months), 

you should repeat charging it several times to achieve the normal battery capacity.   

* Do not recharge the battery if it has been fully charged or the battery power doesn’t become low, 

otherwise it might affect the battery life or performance. Remove the battery from the charger 

after charging.   

* If the radio enters low power warning state, please recharge the battery. Do not use the radio in 

low power state, which will affect the battery life and performance. 

 

Installing/Removing the Battery Pack   

    

Installing/Removing the Battery Pack   

when install the battery, please put the battery into groove on the top of the main board back about 

5mm away from buckle.   

If main board is already installed belt clip, it will need to press to ensure the battery into the clip. 

Press the battery with your fingers and push back to the tank to hear a click sound, the battery is 

installed

 

 

 

     

   

Removing the battery pack:

 

    If you want to pick off the battery from the radio, firstly please press 
the battery button which is located on the bottom side of the radio, and press 
the battery about 5mm gap then take off the battery. 

                                                                                            5 

Summary of Contents for CU600-1

























Reviews: