background image

Warning

FCC

                                             

 

Instruction Manual 

 

Thank you for purchasing a 

COVALUE

 two-way radio. This simple to use radio adopts the latest 

advances in technology, providing reliable communication in today’s demanding communication 

environment.  

 

Notice to the User: 

·

  Please read this instruction manual before operating this radio.   

·

  It’s prohibited to use the radio or charge it at any area with a potentially explosive atmosphere 

(where the air contains gas, dust and smog, etc.), as well as while taking on fuel, or while 

parking at a gasoline service station; or any area where radio communication is prohibited 

(such as a hospital or an airport.) 

·

  It’s prohibited to operate the radio without permission in areas where the government laws 

prohibit radio communication. 

·

  Please don't expose the radio to direct sunlight for a long time; Don't place the radio near any 

heating devices, either. 

·

  Please don't put the radio in extremely dusty, moist humid areas or unstable surfaces. 

·

  Only qualified personal, with proper tools and instruments are allowed to service and repair the 

radios, do not disassemble the radio by yourself to avoid damages. 

 

Any Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions:    (1) This device may not cause harmful interference , and (2) 

this device must accept any interference received , including interference that may 

cause undesired operation . Note: This equipment has been tested and found to comply 

with the limits for a Class B digital          device,    pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference 

in a residential installation. This equipment generates uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is no guarantee 

that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning 

Two way radio

DP7000-2 , DP7100-2 , DP6100-2 , DP6000-2

Summary of Contents for DP6000-2


























Reviews: