CPI GP8 Operating Instructions Manual Download | Manualshive

Page: 7 / 24

background image

Page - 8

SALES + SERVICE

CPIGP8AOPINST

(866) 912-3469

WWW.CPISHINE.COM

INSTALLATION INSTRUCTIONS

UNPACKING THE MACHINE

The machine is delivered packed in a cardboard box containing compressed

polystyrene. Dispose of the packing material according to the requirements of the local

recycling laws.

Verify the machine's integrity and in particular the electric cables. If in doubt, ask a technician

to check before proceeding with installation.

POSITIONING THE GLASS POLISHER



The machine does not require anchoring - but must be level on whatever surface it is

sitting on. This may require the adjustment of the nut located at the base of each leg.



Make sure that no objects (cloths, etc.) are placed under the glass drier so as not to

obstruct air flow.



Ensure the glass drier is not placed close to any taps and/or water connections.

ASSEMBLING THE BRUSHES

Each glass polisher is packaged with 8 brushes and these brushes are colour coded (red,

yellow and green) at the bottom of the brush base. On the top of each support (B) is a coloured

dot corresponding to the brush colours (red, yellow and green).

Place each brush on top of support (B) (matching the colours) and slide the brush down the

support. Ensure that slot (A) is connected by slightly rotating the brush in a clockwise

direction. If the brush is not properly fixed on the support, it will not rotate once the machine is

switched on.

«
...
5
6
7
8
9
...
»

Summary of Contents for GP8

























Reviews:

No comments

Related manuals for GP8

Brand: F.F. Group Pages: 60

Brand: CARPOINT Pages: 12

Brand: Makita Pages: 44

Brand: Makita Pages: 48

Brand: Makita Pages: 32

Brand: PowerTec Pages: 12

Brand: Emax Pages: 8

Brand: Global Pages: 4

Brand: Craftex Pages: 17

Brand: Skil Pages: 100

Brand: Certa Pages: 12

ROS 125/430 PLUS

Brand: F.F. Group Pages: 36

Brand: Raider Pages: 94

Brand: Facom Pages: 40

Brand: Lagler Pages: 68

Brand: Fast Mover Pages: 8

Brand: jcb Pages: 20

Brand: Fast Mover Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands