background image

 

2

 
 

TABLE OF CONTENTS 

 

General Safety Instructions for Pneumatic Tools ...................................................  3 

CX901 Specific Safety Instructions ........................................................................  4 

CX901 Features .....................................................................................................  5 

Unpacking ..............................................................................................................  6 

Inventory.................................................................................................................  6 

Safety Nose Mechanism ........................................................................................  6 

Oiling the Nailer......................................................................................................  7 

Loading the Nailer ..................................................................................................  7 

Operating the Nailer ...............................................................................................  7 

Removing the Jammed Nails..................................................................................  8 

Cleaning .................................................................................................................  8 

Parts Diagram ........................................................................................................  9 

Parts List................................................................................................................. 10 

Warranty ................................................................................................................. 12 

 

Summary of Contents for CX901













Reviews: