background image

10

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE)

See Figure 2.

The direction of bit rotation is reversible and is controlled 
by a selector located above the switch trigger. With the 
drill held in normal operating position, the direction of 
rotation selector should be positioned to the left of the 
switch trigger for drilling. The drilling direction is reversed 
when the selector is to the right of the switch trigger. 

CAUTION:

 

To prevent gear damage, always allow 

the chuck to come to a complete stop before chang-
ing the direction of rotation. 

To stop the drill, release the switch trigger and allow the 
chuck to come to a complete stop.

SPINDLE LOCK

The spindle lock allows the user to keep the chuck from 
turning while changing bits and chucks.

WARNING

:

 

Do not allow familiarity with tools

to make you careless. Remember that a careless 
fraction of a second is sufficient to inflict serious 
injury.

WARNING

:

 

Always wear safety goggles or safety 

glasses with side shields when operating power 
tools. Failure to do so could result in objects being 
thrown into your eyes resulting in possible serious 
injury.

WARNING

Do not attempt to modify this tool 

or create accessories not recommended for use 
with this tool. Any such alteration or modification is 
misuse and could result in a hazardous condition 
leading to possible serious personal injury.

APPLICATIONS

You may use this tool for the purposes listed below:

Drilling in wood

�Drilling in ceramics, plastics, fiberglass, and laminates

�Drilling in both hard and soft metals

Using driving accessories, such as driving screws with 
screwdriver bits����

Mixing paint

SWITCH TRIGGER

See Figure 2.

To turn the drill ON, depress the switch trigger. To turn it 

OFF

, release the switch trigger.

VARIABLE SPEED

The variable speed switch trigger delivers higher speed 
and torque with increased trigger pressure and lower 
speed with decreased trigger pressure.

NOTE: 

You might hear a whistling or ringing noise from 

the switch during use. Do not be concerned; this is a nor-
mal part of the switch function.

KEYLESS CHUCK

See Figure 2.

The keyless chuck is used to install and remove bits.

WARNING:

 

Do not hold the chuck body with one 

hand and use the power of the drill to tighten the 
chuck jaws on the drill bit. The chuck body could slip 
in your hand, or your hand could slip and come in 
contact with the rotating drill bit. This could cause an 
accident resulting in serious personal injury.

Fig. 2

SWITCH 

TRIGGER

OPERATION

DIRECTION OF 

ROTATION SELECTOR

REVERSE

FORWARD

LOCK-ON 

BUTTON

Summary of Contents for 315.101140















Reviews: