background image

11

OPERATION

REMOVING BITS

See Figure 3.

n

  Unplug the drill.

n

  Depress the spindle lock button.

n

  While keeping the button depressed, rotate the chuck 

in either direction until it clicks into a position that will 
not allow it to rotate.

n

  Keeping the spindle lock button depressed, rotate the 

chuck counterclockwise to open the chuck jaws.

n

  Remove the drill bit.

RIGHT

WARNING: 

Make sure to insert the drill bit straight 

into the chuck jaws. Do not insert the drill bit into the 
chuck jaws at an angle then tighten, as shown in fig-
ure 4. This could cause the drill bit to be thrown from 
the drill, resulting in possible serious personal injury 
or damage to the chuck.

NOTE:

 Rotate the chuck body in the direction of the arrow 

     marked 

LOCK

 to tighten the chuck jaws.

n

  Rotate the chuck clockwise to tighten the chuck jaws 

securely on the bit.

n

  Rotate the chuck body slightly to release the spindle 

lock.

Fig. 4

WRONG

INSTALLING BITS

See Figures 3 - 4.

n

  Unplug the drill.

n

  Depress the spindle lock button.

n

  While keeping the button depressed, rotate the chuck 

in either direction until it clicks into a position that will 
not allow it to rotate.

n

  Keeping the spindle lock button depressed, rotate the 

chuck counterclockwise to open the chuck jaws.

n

  Insert the drill bit.

Fig. 3

DRILL BIT

UNLOCK

(RELEASE)

CHUCK 

JAWS

LOCK

(TIGHTEN)

CHUCK 

BODY

DEPRESS SPINDLE LOCK

BUTTON TO ENGAGE

Summary of Contents for 315.101140















Reviews: