background image

8

FEATURES

PRODUCT SPECIFICATIONS

Switch Trigger.............................................Variable Speed
Chuck ...................................3/8 in. Single Sleeve Keyless
No Load Speed ...............................................0-1500/min.

Torque....................................................Maximum 76 in.lb.
Input ................................120 V, 60 Hz, AC only, 5.5 Amps
Net Weight................................................. 3.5 lbs. (1.6 kg)

Fig. 1

 SWITCH

TRIGGER

KEYLESS 

CHUCK 

LOCK-ON 

BUTTON

KNOW YOUR ELECTRIC DRILL

See Figure 1.

Before attempting to use this product, familiarize yourself 
with all operating features and safety rules.

LIVE TOOL INDICATOR

The live tool indicator light is located on the handle of the 
drill and indicates that the tool is connected to a power 
supply.

BUBBLE LEVELS

Bubble levels are recessed in the motor housing and are 
used to keep drill bits level during both horizontal and 
vertical drilling operations.

VARIABLE SPEED

The variable speed switch trigger delivers higher speed 
with increased trigger pressure and lower speed with de-
creased trigger pressure.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE)

Your drill has a direction of rotation (forward/reverse) selector 
located above the switch trigger for changing the direction 
of bit rotation. 

SPINDLE LOCK 

The spindle lock feature allows user to keep the chuck 
from turning while changing bits and chucks.

KEYLESS CHUCK 

The keyless chuck allows you to hand-tighten or release the 
drill bit in the chuck jaws.

LIVE TOOL 

INDICATOR

 

LEVELS

DIRECTION OF 

ROTATION SELECTOR

SPINDLE LOCK 

BUTTON

Summary of Contents for 315.101140















Reviews: