Craftsman 486.242112 Owner'S Manual Download

Page: 10 / 16

ATTACHING SWEEPER HITCH TO TRACTOR

BLACK LINE IS TRACTOR HITCH

HITCH BRACKET MOUNTED
BELOW HITCH TUBES

BLACK LINE IS TRACTOR HITCH

HITCH BRACKET MOUNTED
ABOVE HITCH TUBES

• Place the tractor and sweeper on a ﬂ at level surface.

• Set the sweeper height adjustment handle to about the

middle of its adjustment range.

• Attach the sweeper hitch to the tractor hitch, arranging

the 3/4" spacers in one of six possible combinations as
shown in GROUP A and GROUP B diagrams below.

IMPORTANT: To obtain the best performance from your
sweeper, arrange the spacers so that the sweeper bag is
approximately level with the ground and approximately 5"
to 7" off the ground as shown in ﬁ gure 19.

GROUP "B" - For vehicles with hitches
having 10" to 13" ground clearance.

GROUP "A" - For vehicles with hitches
having 8" to 10" ground clearance.

APPROXIMATELY LEVEL
(5" to 7" FROM SURFACE)

BRUSH HEIGHT ADJUSTED
APPROXIMATELY MID-WAY

Summary of Contents for 486.242112

















Search results

Summary of Contents for 486.242112

Reviews:

Related manuals for 486.242112

Brands by name

Popular brands

Craftsman 486.242112, Owner'S Manual

Search results

Summary of Contents for 486.242112

Reviews:

Related manuals for 486.242112

Brands by name

Popular brands