Craftsman 486.24222 Owner'S Manual Download

Page: 8 / 16

STEP 14 - ASSEMBLE HOPPER CLAMPS

• Assemble two hopper mount clamps (Q) over the hole

in the middle of each upper hopper tube using two
carriage bolts ( E) and two nylock nuts (F). Tighten
only ﬁ nger tight. See ﬁ gure 14.

• Fold the bag ﬂ aps around the lower hopper tubes and

attach to the bag bottom using the snaps. See ﬁ gure
13.

FIGURE 13

STEP 13 - ATTACH BAG BOTTOM

• Insert the bag frame strap into the stitched sleeve at

the front edge of the bag bottom. See ﬁ gure 11.

FIGURE 12

FIGURE 14

CLEVIS PIN (O)

HAIR COTTER
PIN (M)

BAG FRAME STRAP

SNAP

FLAP

BAG FRAME STRAP

STITCHED
SLEEVE

• Assemble the bag frame strap to the holes in the

lower hopper tubes using two clevis pins (O) and hair
cotter pins (M). See ﬁ gure 12.

FIGURE 11

5/16" x 3/4"
CARRIAGE
BOLT (E)

5/16" NYLOCK
NUT (F)

HOPPER
MOUNT
CLAMP (Q)

UPPER
HOPPER
TUBE

Summary of Contents for 486.24222

















Search results

Summary of Contents for 486.24222

Reviews:

Related manuals for 486.24222

Brands by name

Popular brands

Craftsman 486.24222, Owner'S Manual

Search results

Summary of Contents for 486.24222

Reviews:

Related manuals for 486.24222

Brands by name

Popular brands