background image

13

CARBURETOR

Your carburetor is not adjustable.  If your 
engine does not operate properly due to 
suspected carburetor problems, take your 
lawn mower to a Sears or other qualifi ed 
service center for repair or ad just ment.

IMPORTANT:

  Never tamper with the 

engine governor, which is factory set 
for proper engine speed.  Over speed ing 
the engine above the factory high speed 
setting can be dangerous.  If you think 
the engine-governed high speed needs 
adjusting, contact a Sears or other 
qualifi ed service center, which has proper 
equip ment and ex pe ri ence to make any 
nec es sary adjustments.

STORAGE

Immediately prepare your lawn mower for 
storage at the end of the season or if the 
unit will not be used for 30 days or more.

LAWN MOWER

When lawn mower is to be stored for a 
period of time, clean it thor oughly, remove 
all dirt, grease, leaves, etc.  Store in a 
clean, dry area.
1.   Clean entire lawn mower (See 

“CLEANING” in the Maintenance sec-
tion of this manual).

2.   Lubricate as shown in the Main te nance 

section of this manual.

3.   Be sure that all nuts, bolts, screws, and 

pins are securely fas tened.  Inspect   
moving parts for damage, breakage 
and wear.  Replace if necessary.

4.   Touch up all rusted or chipped paint 

surfaces; sand lightly before painting.

HANDLE 

You can fold your lawn mower handle for 
storage.

NOTE: 

The upper handle has an "anti-

fold" bracket located on the right side of 
the handle.  This bracket prevents the 
upper handle from folding forward, which 
helps protect control cable(s) from dam-
age.
1.   Loosen the two (2) handle knobs on 

sides of the upper handle and allow 
handle to fold down to the rear.

2.   Squeeze the bottom ends of lower 

handle toward each other until pins 
in handle clear the brackets and pivot 
entire handle assembly forward and 
allow it to rest on mower.

•   When setting up your handle from the 

storage position, the lower handle will 
require manually locking into the mow-
ing position.

Handle pin

Handle 
bracket

SQUEEZE

Mowing 
position

Operator presence 
control bar

           FOLD
        FORWARD
     FOR
  STORAGE

Upper handle

Lower 
handle

IMPORTANT:

  When folding the handle for 

storage or trans por ta tion, be sure to fold 
the handle as shown or you may damage 
the control cables.

Summary of Contents for 944.361543

























Reviews: