14
4. Wipe off any spilled oil from lawn
mower or side of engine.
5. Fill engine with oil. The engine oil
capacity is 0.58 quarts. If oil is not
com plete ly drained from engine, you
may not need the entire container of a
20 oz. bottle of oil. Slowly pour 3/4 of
the oil from the container down the oil
fill spout into the engine.
6. Wait one minute to allow oil to settle.
Use guage on oil fill cap/dipstick for
checking level. Insert dipstick into
the tube and rest the oil fill cap on the
tube. DO NOT thread the cap into the
tube when taking reading.
7. Continue adding small amounts of
oil and rechecking the dipstick until it
reads full. DO NOT overfill, or engine
will smoke on startup.
8. Always be sure to retighten oil dipstick
before starting engine.
9. Reconnect spark plug wire to plug.
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or dam age.
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs
first. Spark plug type and gap setting
are shown in the “PROD UCT SPEC I FI CA-
TIONS” section of this manual.
NOTE:
Multi-viscosity oils (5W30, 10W30
etc.) improve starting in cold weather, and
you should check your engine oil level fre-
quently to avoid possible engine damage
from running low on oil.
Change the oil after every 25 hours of opera-
tion or at least once a year if the lawn mower
is not used for 25 hours in one year.
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use. Tighten oil plug
securely each time you check the oil level.
TO CHANGE ENGINE OIL
NOTE
: Before tipping lawn mower to
drain oil, empty fuel tank by running en-
gine until fuel tank is empty.
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3. Tip lawn mower on its side as shown
and drain oil into a suitable container.
Rock lawn mower back and forth to re-
move any oil trapped inside of engine.
Container
Oil fill cap /
dipstick
Lower
mark
Upper
mark
AIR FILTER
Your engine will not run properly and may
be damaged by using a dirty air filter.
Replace the air filter every 100 hours of
operation or every season, whichever oc-
curs first. Service air cleaner more often
under dusty conditions.
TO CLEAN AIR FILTER
1. Remove cover.
2. Carefully remove cartridge.
3. Clean by gently tapping on a flat sur-
face. If very dirty, replace cartridge.
CAUTION:
Petroleum solvents, such
as ker o sene, are not to be used to clean
car tridge. They may cause de te ri o ra tion
of the cartridge. Do not oil car tridge. Do
not use pres sur ized air to clean or dry
car tridge.
4. Install cartridge, then replace cover.
Tab
Cartridge
Filter cover
Slot
19
Loss of power
1. Rear of mower housing or
1. Raise cutting height.
blade dragging in grass.
2. Cutting too much grass.
2. Raise cutting height.
3. Dirty air filter.
3. Clean/replace air filter.
4. Buildup of grass, leaves,
4. Clean underside of mower
and trash under mower.
housing.
5. Too much oil in engine.
5. Check oil level.
6. Walking speed too fast.
6. Cut at slower walking speed.
Poor cut –
1. Worn, bent or loose blade.
1. Replace blade. Tighten
uneven
blade
bolt.
2. Wheel heights uneven.
2. Set all wheels at same
height.
3. Buildup of grass, leaves
3. Clean underside of
and trash under mower.
mower housing.
Excessive
1. Worn, bent or loose blade.
1. Replace blade. Tighten
vibration
blade
bolt.
2. Bent engine crankshaft.
2. Contact a Sears or other
qualified
service
centre.
Starter rope
1. Engine flywheel brake is on 1. Depress control bar to
hard to pull
when control bar is released. upper handle before
pulling the starter rope.
2. Bent engine crankshaft.
2. Contact a Sears or other
qualified
service
centre.
3. Blade adapter broken.
3. Replace blade adapter.
4. Blade dragging in grass.
4. Move lawn mower to cut
grass or to hard surface.
Grass catcher
1. Cutting height too low.
1. Raise cutting height.
not filling
2. Lift on blade worn off.
2. Replace blade.
(If so equipped)
3. Catcher not venting air.
3. Clean grass catcher.
Hard to push
1. Grass is too high or wheel
1. Raise cutting height.
height is too low.
2. Rear of mower housing or
2. Raise rear of mower housing
blade dragging in grass.
one (1) setting higher.
3. Grass catcher too full.
3. Empty grass catcher.
4. Handle height position not 4. Adjust handle height to suit.
right for you.
PROBLEM CAUSE
CORRECTION
TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Parts & Repair Centre.
