background image

24

CRAFTSMAN 

ROT

ARY LA

WN MOWER - - MODEL NUMBER  

944.364701

33

40

12

13

14

15

16

18

26

27

4

27

4

28

28

29

29

30

30

30

31

31

34

34

35

36

37

55

18

18

18

22

22

59

59

20

25

22

86

87

32

32

33

33

33

40

1

7

9

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED 

Engine speed was set at the factory for 

optimum performance. It is not adjustable.

ENGINE ZONE CONTROL

 

CAUTION:

  Federal regulations re quire 

an engine control to be installed on this 

lawn mower in order to minimize the risk 

of blade contact injury. Do not un der 

any circumstances attempt to de feat the 

func tion of the operator con trol. The blade 

turns when the engine is running.

•  Your lawn mower is equipped with an 

operator pres ence control bar which 

requires the operator to be positioned 

behind the lawn mower handle to start 

and operate the lawn mower.

TO OPERATE DRIVE SYSTEM 

•  To start forward motion, lift drive con-

trol bar up to handle.

•  To stop forward motion, release drive 

control bar.

IMPORTANT

:  Always keep drive control 

fully engaged against handle when in use.

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels 

for high cut, adjust cutting height to suit 

your requirements. Me di um position is 

best for most lawns.

•  To change cutting height, squeeze ad-

juster lever to ward wheel. Move wheel 

up or down to suit your re quire ments. 

Be sure all wheels are in the same set-

ting.

NOTE: 

Adjuster is properly positioned 

when plate tab inserts into hole in lever. 

Also, 9-position adjusters (if so equipped) 

allow lever to be positioned between the 

plate tabs.

TO CONVERT MOWER

Your lawn mower was shipped ready to 

be used as a mulcher.  To convert to bag-

ging or discharging:

REAR BAGGING 

•  Lift rear door of the lawn mower and 

place the grass catcher frame hooks 

onto the grass bag brackets.

•  To convert to mulching or dis charg ing 

operation, remove grass catch er and 

close rear door.

Grass bag 

bracket

Grass 

catcher 

handle

Grass catcher 

frame hook

Rear door

DRIVE CONTROL ENGAGED

Operator 

pres ence 

con trol bar

DRIVE CONTROL DIS EN GAGED

Drive 

con trol 

bar

ROTATE LEVER TOWARD 

ENGINE TO LOWER MOWER

ROTATE LEVER AWAY FROM ENGINE 

TO RAISE MOWER

Plate tab

Lever

The operation of any lawn mower can result in foreign objects 

thrown into the eyes, which can result in severe eye damage.  

Always wear safety glasses or eye shields while operating your 

lawn mower or performing any adjustments or repairs.  We recom-

mend standard safety glasses or a wide vision safety mask over spectacles.

Use ear 

protec-

tors to 

a v o i d 

damage to hearing.

Summary of Contents for 944.364701

















Reviews: