background image

22

CRAFTSMAN 

ROT

AR

Y

 LA

WN MOWER - - MODEL

 NUMBER  

944.364720

REPAIR PARTS

1

3

7

8

9

21

30

31

32

33

36

53

38

39

42

44

45

46

47

48

49

50

51

52

53

57

22

34

53

57

28

28

22

34

40

56

41

41

43

53

97

59

13

11

17

26

56

56

58

59

11

26

59

24

20

83

85

2

6

6

6

6

84

96

18

19

64

11

TO STOP ENGINE

•  To stop engine, release operator pres-

ence con trol bar.

TO START ENGINE 

NOTE:

 Due to protective coatings on the 

engine, a small amount of smoke may be 
present during the initial use of the product 
and should be considered normal.

NOTE:

  Your engine is equipped with an 

automatic choke system.  No priming or 
choking is required before starting.
•  To start engine, hold operator presence 

control bar down to the han dle and pull 
starter handle quickly. Do not allow 
starter rope to snap back. 

BEFORE STARTING ENGINE

ADD OIL

Your lawnmower is shipped without oil in 
the engine. For type and grade of oil to 
use, see “EN GINE” in the Maintenance 
section of this manual.

  CAUTION:

 DO NOT overfi ll engine with 

oil, or it will smoke heavily from the muffl er 
on startup.
1.  Be sure lawnmower is level.  
2.  Remove oil dipstick from oil fi ll spout.
3.  You receive a container of oil with the 

unit.  Slowly pour the entire container 
down the oil fi ll spout into the engine.

NOTE: 

Initial oil fi ll requires only 18 oz. 

due to residual oil in engine from the 
manufacturers 100% quality testing. When 
changing oil you may need 20 oz.
4.  Insert and tighten dipstick.

IMPORTANT:

•  Check oil level before each use.  Add oil 

if needed.  Fill to full line on dipstick.

•  Change the oil after every 25 hours of 

operation or each season.  You may 
need to change the oil more often 
under dusty, dirty conditions.  See “TO 
CHANGE ENGINE OIL” in the Mainte-
nance section of this manual.

ADD GASOLINE

•  Fill fuel tank to bottom of tank fi ller neck.  

Do not overfi ll.  Use fresh, clean, regular 
unleaded gasoline with a minimum of 
87 octane.  Do not mix oil with gasoline.  
Purchase fuel in quan ti ties that can be 
used within 30 days to assure fuel fresh-
ness.

  CAUTION:  

Wipe off any spilled oil or 

fuel.  Do not store, spill or use gasoline 
near an open fl ame.

  CAUTION

:  Alcohol blended fuels 

(called gasohol or using ethanol or metha-
nol) can attract moisture which leads to 
separation and for ma tion of acids during 
storage.  Acidic gas can damage the fuel 
system of an engine while in storage.  To 
avoid engine problems, the fuel system 
should be emptied before stor age of 30 
days or longer.  Empty the gas tank, start 
the engine and let it run until the fuel lines 
and carburetor are empty.  Use fresh fuel 
next season.  See Storage In struc tions for 
additional information.  Never use engine 
or carburetor cleaner products in the fuel 
tank or permanent damage may occur.

Engine 

oil cap

Gasoline 
fi ller cap

Summary of Contents for 944.364720

















Reviews: