Craftsman 944.364720 Owner'S Manual Download

Page: 7 / 16

MODEL NUMBER 126M02-0303-F4

BRIGGS & STRATTON 4-CYCLE ENGINE

TO ASSEMBLE GRASS CATCH ER

1. Put grass catcher frame into grass bag

with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.

2. Slip vinyl bindings over frame.

NOTE

: If vinyl bindings are too stiff, hold

them in warm water for a few minutes. If
bag gets wet, let it dry before using.

Frame

opening

Vinyl
bindings

Frame

handle

INSTALL STARTER ROPE

1. Loosen T-knob.
2. Hold control bar against upper handle.
3. Slowly pull engine starter rope out until

rope will slip into loop of rope guide.

4. Tighten T-knob.

Upper handle

Control bar

Engine
starter rope

Rope guide

T-Knob

TO INSTALL ATTACHMENTS

Your lawn mower was shipped ready to be
used as a mulcher. To convert mower to
bagging or discharging, see “TO CON-
VERT MOWER” in the Operation section
of this manual.

Summary of Contents for 944.364720

















Search results

Summary of Contents for 944.364720

Reviews:

Related manuals for 944.364720

Brands by name

Popular brands

Craftsman 944.364720, Owner'S Manual

Search results

Summary of Contents for 944.364720

Reviews:

Related manuals for 944.364720

Brands by name

Popular brands