Craftsman CMCE003, Instruction Manual

English

8

Cleaning

WARNING:

 Blow dirt and dust out of all air vents with 

clean, dry air at least once a week. To minimize the risk 
of eye injury, always wear ANSI Z87.1 approved eye 
protection when performing this procedure.

Nozzle Maintenance (Fig. E, I, J)

Ensure all misting nozzle maintenance is properly performed.
Leaks can result creating a slip and fall hazard or cause 
property damage. Irregular mist patterns or leakage may be 
the result of a clogged or dirty misting nozzle.

To Clean Nozzles

1.  Turn off the fan and the pump.
2.  Remove the battery pack 

 8 

.

3.  Remove the misting nozzles 

 5 

 from each side of the fan 

by rotating them in a counterclockwise direction.

4.  Soak the misting nozzles in a de-scaling agent for at least 

an hour.

5.  Use a brush to clean any foreign materials restricting the 

misting nozzles in the front and rear holes while rinsing 
with water.

6.  Flush the misting nozzles with water.
7.  Reconnect the misting nozzles.

MAINTENANCE

WARNING: To reduce the risk of  serious personal 

injury, turn unit off and remove the battery pack 

before making any adjustments or removing/

installing attachments or accessories.

 An 

accidental start‑up can cause injury.

Your CRAFTSMAN power tool has been designed to operate 
over a long period of time with a minimum of maintenance. 
Continuous satisfactory operation depends upon proper tool 
care and regular cleaning.

Usage with Garden Hose (Fig. H)

CAUTION:

 Do not allow water to continue to flow 

when the fan is off

1.  Set the fan base onto a flat, stable surface.
2.  Attach the garden hose 

 10 

 (not included) to the intake 

tube head 

 4 

, and hand tighten the hose by rotating the 

connector thread. 

nOTE

: Do not secure the intake tube in the storage 

clips 

 11 

 while attached to the garden hose. The storage 

clips are only for storage when not in use

3.  Choose the appropriate setting for the pump. Refer to 

Pump Switch

 for further information.

4.  Set your fan setting. Refer to 

Turning the Fan On and Off

for further information.

4.  Choose the appropriate setting for the pump. Refer to 

Pump Switch

 for further information.

5.  Set your fan setting. Refer to 

Turning the Fan On and Off

for further information. 

nOTE

: The fan and water bucket must be moved 

seperately. The fan is not attached to the water bucket. 

Usage with Water Bucket (Fig. F, G)

WARNING:

  Do not submerge the fan in the 

water bucket.

1.  Place the water bucket 

 12 

 (not included) on a flat and 

level surface.

2.  Fill the water bucket with plain, clean water with no 

other additives. Do not fill the bucket so it overflows.

3.  Set the fan base onto the rim of the water bucket so the 

intake tube head 

 4 

 is submerged in the water. 

nOTE

: Do not secure the intake tube 

 7 

in the storage 

clips 

 4 

 while pumping water from the water bucket. The 

storage clips are only for storage when not in use

Pump Switch (Fig. A)

•  To turn the pump on low, press the pump button 

 2 

once. When turning on the pump, the fan will be turned 
on automatically at low speed.

•  To turn the pump on medium, press the pump 

button twice.

•  To turn the pump on high, press the pump button 

three times.

•  To turn the pump switch off, press the pump button a 

fourth time for 1 second. The pump will turn off from any 
on setting.

Turning the Fan On and Off (Fig. A)

Fan speed is variable and can be adjusted by the fan 
button 

 1 

.

To turn the fan on low, press the fan button once.
To turn the fan on medium, press the fan button twice.
To turn the fan on high, press the fan button three times.
To turn off the fan, press the fan button for a fourth time for 
1 second. The pump will turn off from any on setting.

nOTE:

 If you turn on the pump only, the fan will turn on to 

the lowest setting.

Installing and Removing the Battery Pack 

(Fig. E)

CAUTION:

 Make sure the battery compartment door is 

closed before operating the fan. 

DO NOT

 allow water 

to enter the battery compartment

nOTE:

 For best results, make sure your battery pack is 

fully charged.
To install the battery pack 

 8 

 into the fan, open the battery 

compartment door 

 6 

. Align the battery pack with the rails 

inside the fan's battery compartment and slide it in until 
the battery pack is firmly seated and ensure that it does 
not disengage. Shut the battery compartment door. 
To remove the battery pack from the fan, open the battery 
compartment door. Press the release button 

 9 

 and firmly 

pull the battery pack out of the fan's battery compartment. 
Insert it into the charger as described in the charger section 
of this manual.

installing attachments or accessories.

 An 

accidental start‑up can cause injury.

WARNING:

 Do not aim toward electrical or other 

risk areas.