background image

3

TABLE OF CONTENTS

SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES................................. 4
WARRANTY................................................................... 4
ASSEMBLY ................................................................. 6-8
OPERATION ............................................................. 9-13
MAINTENANCE SCHEDULE ...................................... 14

MAINTENANCE ...................................................... 14-17
SERVICE AND AD JUST MENTS ............................ 18-23
STORAGE .................................................................... 24
TROU BLE SHOOT ING ............................................ 25-26
REPAIR PARTS - TRACTOR .................................. 28-43
REPAIR PARTS - ENGINE...................................... 44-49
PARTS ORDERING/SERVICE.........................................
BACK COVER..................................................................

WARNING:  In order to prevent ac ci den tal 
starting when setting up, trans 

port ing, 

ad just ing or making repairs, al ways dis-
 con nect spark plug wire and place wire 
where it cannot contact spark plug. 

•           Be sure the area is clear of other people before mowing. Stop 

machine if anyone enters the area.

•      Never carry passengers or children even with the blades 

off.

•      Do not mow in reverse unless absolutely necessary. Al ways 

look down and behind before and while backing.

•           Never carry children. They may fall off and be seriously injured 

or interfere with safe machine operation.

•       Keep children out of the mowing area and under the watchful 

care of another responsible adult.

•      Be alert and turn machine off if children enter the area.
•      Before and when backing, look behind and down for small 

children.

•      Mow up and down slopes (15° Max), not across.
•      Remove obstacles such as rocks, tree limbs, etc.
•           Watch for holes, ruts, or bumps. Uneven terrain could over turn 

the machine. Tall grass can hide obstacles.

•       Use slow speed. Choose a low gear so that you will not have 

to stop or shift while on the slope.

•      Avoid starting or stopping on a slope. If tires lose traction, 

disengage the blades and proceed slowly straight down the 
slope.

•      If machine stops while going uphill, disengage blades, shift 

into reverse and back down slowly.

•           Do not turn on slopes unless necessary, and then, turn slowly 

and gradually downhill, if possible.

WARNING:  Do not coast down a hill in neu-
tral, you may lose control of the trac tor.

WARNING:  Tow only the at tach ments that 
are recommended by and com 

ply with 

specifi cations of the man u fac tur er of your 
tractor.  Use common sense when towing.    
Operate only at the lowest pos si ble speed 
when on a slope.  Too heavy of a load, while 
on a slope, is dan ger ous.  Tires can lose 
trac tion with the ground and cause you to 
lose control of your tractor.

Safe Operation Practices for Ride-On Mowers

SAFETY RULES

Summary of Contents for Sears 944.603150












































Reviews: