Crane Weinman B Series Installation And Operation Manual Download | Manualshive

Page: 14 / 16

background image

START-UP REPORT

General Information

Pump Owner’s Name: __________________________________________________________
Address: ____________________________________________________________________
Location of Installation: _________________________________________________________
Contact Person: __________________________________Phone: _______________________
Purchased From: _____________________________________________________________

Nameplate Data

Pump Model #: ___________________ Serial #: _____________________________________
Part #: __________________________ Impeller Diameter: ____________________________
Voltage: _________Phase: _____ Ø

Hertz: ____________Horsepower: _______________

Full Load Amps: ___________________ Service Factor Amps: __________________________
Motor Manufacturer: ___________________________________________________________

Controls

Control panel manufacturer: _____________________________________________________
Model/Part number: ____________________________________________________________
Number of pumps operated by control panel: ________________________________________
Short circuit protection? YES___ NO___

Type: _________________________________

Number and size of short circuit device(s): ___________   Amp rating:  ___________________
Overload Type:  _____________ Size: ______________   Amp rating:  ___________________
Do protection devices comply with pump and motor Amp rating?   YES___ NO___
Are all electrical and panel entry connections tight?   YES___ NO___
Is the interior of the panel dry?   YES___ NO___
Liquid level Control Brand and Model: ______________________________________________

Pre-Startup

All Pumps

Type of equipment: NEW___ REBUILT___ USED___
Condition of equipment at Start-Up: DRY___ WET___ MUDDY___
Was Equipment Stored? YES___ NO___

Length of Storage: ______________________

Liquid being pumped:  __________________   Liquid Temperature:  _____________________
Supply Voltage/Phase/Frequency matches nameplate?   YES___ NO___
Shaft turns freely?   YES___ NO___
Direction of rotation veri

fi

ed for 3Ø motors? YES___ NO___

Debris in piping or wet well? YES___ NO___
Debris removed in your presence? YES___ NO___
Pump case/wet well

fi

lled with liquid before startup? YES___ NO___

Is piping properly supported? YES___ NO___

Non-Submersible Pumps

Is base plate properly installed / grouted? YES___ NO___ N/A___
Coupling Alignment Veri

fi

ed per I&O Manual? YES___ NO___ N/A___

Grease Cup/Oil Reservoir Level checked? YES___ NO___ N/A___

A Crane Co. Company

«
...
12
13
14
15
16
»

Summary of Contents for Weinman B Series

















Reviews:

No comments

Related manuals for Weinman B Series

Brand: Gardena Pages: 182

Brand: Eccotemp Pages: 56

Brand: Waters Pages: 111

Brand: Samoa Pages: 32

Brand: Daikin Pages: 30

Brand: Pentair Pool Products Pages: 2

RJS-75SS Series

Brand: red lion Pages: 32

Brand: Trane Pages: 8

Brand: Viessmann Pages: 52

Brand: T.I.P. Pages: 104

Brand: Honda Pages: 25

Brand: GASLAND chef Pages: 60

Brand: Wacker Neuson Pages: 46

EcoPart 400 230V 1N~

Brand: CTC Union Pages: 40

Brand: W'eau Pages: 32

LX ACDC/M+K 100 A

Brand: Logitex Pages: 18

Brand: Little Giant Pages: 16

Brand: CTC Union Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands