background image

 

16 

Troubleshooting 
 

1. 

The detector does not turn on.

  Check the batteries. If they are 

old replace them with new. Make sure the batteries are properly 
inserted into the battery holder and have a good electrical contact. 

2. 

The detector is giving too many false signals. 

 If this happens 

first turn the Sensitivity to 0, minimum level. Check the Ground 
Balance if it is adjusted correctly according to the ground balance 
procedure. If the problem still persist check if the soil does not 
contain hot rocks or other contaminants. If this is the case then use 
Silent Motion and /or Iron Rejection to stop the interference. Auto 
mode will also assist in such conditions.

 

3. 

The detector is picking up too much Iron. 

Check the 

Discrimination level according to the recommended settings or use 
Auto mode.

 

4. 

I only plug the search coil and detector does not work after 
that. 

Make sure that it is the correct search coil for your Nexus 

model. The search coils for Credo DDM are not interchangeable 
with the Nexus Standard MkII and vice versa.

 

5. 

One or more control functions does not work. 

Make sure that 

you know how to use those control functions according to this User 
Manual. In case that any of the control functions do not cause any 
change of response in the detector functions then return the 
detector to your dealer for check and possible repair.

 

6. 

The detector is unstable. 

Make sure 

not to

 use the detector with 

full Sensitivity while using fast Recovery speed setting. Fast 
Recovery setting and high Sensitivity together will result in 
considerable amount of chatter in the loudspeaker and/or 
headphones. If this is not the case check for sources of electronic 
interference. 

 

7. 

The detector stopped working during rain. 

Nexus detectors are 

not water or weather proofed. Knowing that we strongly 
recommend that no Nexus metal detector model is used in rain. If 
this happens turn off the power of the detector from the Volume 
knob. Take out the batteries and leave the detector near a warm 
place for a couple of days to dry out. After that if still not working 
return the detector to your dealer for maintenance and repair.

 

  
 
 
 
 
 
 

Summary of Contents for Metal Detector


















Reviews: