background image

DO

 

GUIDE

DOC. 7864C (2045550) 06.17

Specifications subject to change without notice.

Set Cresnet ID

Tap button 1 to enter the Cresnet ID screen.

Tap button 5 or button 6 to raise or lower the Cresnet ID.  
Tap button 2 to save the Cresnet ID. Tap button 3 to exit the screen 
without saving. 

Set Panel Lights

Tap button 5 to enter the Panel Lights screen. The Panel  
Lights screen allows the light settings to be changed for the  
sensor, screen, timeout, and button options.

View Firmware Version

Tap button 2 to view the firmware version of the C2N-LCDB3. 

Restore the Keypad

Tap button 6 to restore the keypad back to its factory settings.

Exit Setup Screen

Tap button 3 from the setup screen to exit setup.

DO

 Learn More

Visit the website for additional information and 
the latest firmware updates. To learn more about 
this product, use a QR reader application on your 
mobile device to scan the QR image.

Crestron Electronics

 

15 Volvo Drive, Rockleigh, NJ 07647 
888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.  

This product is Listed to applicable UL

®

 Standards and requirements tested by Underwriters Laboratories Inc. 

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference 
that may cause undesired operation.

CAUTION:

  Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the 

user’s authority to operate the equipment.

NOTE: 

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the 

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 

• Reorient or relocate the receiving antenna.

 

• Increase the separation between the equipment and receiver.

 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement 

CAN ICES-3(B)/NMB-3(B)

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools 
License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements 
can be found on the Crestron website at 

www.crestron.com/legal/software_license_agreement

.

The specific patents that cover Crestron products are listed at 

http://www.crestron.com/legal/patents

The product warranty can be found at 

www.crestron.com/warranty

.

Certain Crestron products contain open source software. For specific information, please visit 

www.crestron.com/opensource

Crestron, the Crestron logo, 3-Series Control System, and Cresnet are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL 
and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and 
trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of 
others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron. 
©2017 Crestron Electronics, Inc.

Reviews: