background image

Terminal Block & Module   

Crestron 

CLT- & CLX-2DIM2

 

4  

  Terminal Block & Module:  CLT- & CLX-2DIM2 

Installation Guide – DOC. 5988B 

6.  If the program is not running yet, loads can be 

tested by using Local Mode. 
 

Use Local Mode to verify that each load is connected to 
the proper output on the modules.  

1. Press 

the 

SETUP

 button momentarily (less than 

three seconds) to enter Local Mode. 
The 

SETUP

 LED and output LED 

1

 illuminate 

and power is applied to the devices connected to 
output 

1

.  

2. Press 

the 

SETUP

 button again to turn off output 

1

 and turn on output 

2

.  

3. Press 

the 

SETUP

 button again for each output 

that needs to be tested.  

4.  After turning on the last output, press the 

SETUP

 button again to turn on all outputs. 

5. Press 

the 

SETUP

 button once more to turn off 

all outputs and LEDs and exit Local Mode. 

Further Inquiries 

If you cannot locate specific information or have 
questions after reviewing this guide, please take 
advantage of Crestron's award winning customer service 
team by calling the Crestron corporate headquarters at  
1-888-CRESTRON [1-888-273-7876]. For assistance in 
your local time zone, refer to the Crestron website 
(

www.crestron.com

) for a listing of Crestron worldwide 

offices. 

You can also log onto the online help section of the 
Crestron website to ask questions about Crestron 
products. First-time users will need to establish a user 
account to fully benefit from all available features. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Return and Warranty Policies 

Merchandise Returns / Repair Service 

1. 

No merchandise may be returned for credit, exchange, or 
service without prior authorization from CRESTRON. To 
obtain warranty service for CRESTRON products, contact 
the factory and request an RMA (Return Merchandise 
Authorization) number. Enclose a note specifying the nature 
of the problem, name and phone number of contact person, 
RMA number, and return address. 

2. 

Products may be returned for credit, exchange, or service 
with a CRESTRON Return Merchandise Authorization 
(RMA) number. Authorized returns must be shipped freight 
prepaid to CRESTRON, Cresskill, N.J., or its authorized 
subsidiaries, with RMA number clearly marked on the 
outside of all cartons. Shipments arriving freight collect or 
without an RMA number shall be subject to refusal. 
CRESTRON reserves the right in its sole and absolute 
discretion to charge a 15% restocking fee, plus shipping 
costs, on any products returned with an RMA. 

3. 

Return freight charges following repair of items under 
warranty shall be paid by CRESTRON, shipping by standard 
ground carrier. In the event repairs are found to be non-
warranty, return freight costs shall be paid by the purchaser. 

CRESTRON Limited Warranty 

CRESTRON ELECTRONICS, Inc. warrants its products to be free from 
manufacturing defects in materials and workmanship under normal use 
for a period of three (3) years from the date of purchase from 
CRESTRON, with the following exceptions: disk drives and any other 
moving or rotating mechanical parts, pan/tilt heads and power supplies 
are covered for a period of one (1) year; touchscreen display and overlay 
components are covered for 90 days; batteries and incandescent lamps 
are not covered. 

This warranty extends to products purchased directly from CRESTRON 
or an authorized CRESTRON dealer. Purchasers should inquire of the 
dealer regarding the nature and extent of the dealer's warranty, if any. 

CRESTRON shall not be liable to honor the terms of this warranty if the 
product has been used in any application other than that for which it was 
intended, or if it has been subjected to misuse, accidental damage, 
modification, or improper installation procedures. Furthermore, this 
warranty does not cover any product that has had the serial number 
altered, defaced, or removed. 

This warranty shall be the sole and exclusive remedy to the original 
purchaser. In no event shall CRESTRON be liable for incidental or 
consequential damages of any kind (property or economic damages 
inclusive) arising from the sale or use of this equipment. CRESTRON is 
not liable for any claim made by a third party or made by the purchaser 
for a third party. 

CRESTRON shall, at its option, repair or replace any product found 
defective, without charge for parts or labor. Repaired or replaced 
equipment and parts supplied under this warranty shall be covered only 
by the unexpired portion of the warranty. 

Except as expressly set forth in this warranty, CRESTRON makes no 
other warranties, expressed or implied, nor authorizes any other party to 
offer any warranty, including any implied warranties of merchantability 
or fitness for a particular purpose. Any implied warranties that may be 
imposed by law are limited to the terms of this limited warranty. This 
warranty statement supercedes all previous warranties. 

Trademark Information

 

All brand names, product names, and trademarks are the sole property of their respective 
owners. Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me/XP 
and WindowsNT/2000 are trademarks of Microsoft Corporation.

 

Summary of Contents for CLT-2DIM2

Page 1: ...lock and module must be mounted into a Crestron Automation Enclosure by a licensed electrician in accordance with all national and local codes CAUTION This equipment is for indoor use only and needs to be air cooled Mount in a well ventilated area The ambient temperature must be 32 F to 104 F 0 C to 40 C The relative humidity must be 0 to 90 non condensing Terminal blocks are installed along the l...

Page 2: ...mpers until all feed and load wiring has been completed the circuit has been tested for electrical faults and the module has been installed Refer to Module Installation on next page NOTE Use copper conductors only rated 75 C 2 With the circuit breaker turned off connect the circuit feed HOT and NEUTRAL and controlled circuit LOAD wires to the terminal block per the markings provided on the wiring ...

Page 3: ...the terminal to which it should be connected Wires are pre stripped to inch Tighten to 9 in lbs Do not over tighten 3 If the module is being installed above another module within the enclosure attach the supplied module interconnect cable between the two modules The illustration below depicts the area within a double wide enclosure where the corners of four modules meet NOTE One wire on the module...

Page 4: ...es following repair of items under warranty shall be paid by CRESTRON shipping by standard ground carrier In the event repairs are found to be non warranty return freight costs shall be paid by the purchaser CRESTRON Limited Warranty CRESTRON ELECTRONICS Inc warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three 3 years from ...

Reviews: