Crestron
CNAMPX-16X60
16 Channel Professional Audio Amplifier
Hookup
Refer to the hookup diagram after this paragraph. Other than making the power
connection last, complete the connections in any order. The power cord is supplied
but RCA, speaker, or Cresnet cables are not.
NOTE:
If making four-wire connections to Cresnet devices, review the latest
revision of the network interconnection drawing (Doc. 5411). The document can be
obtained from the Downloads | Product Manuals section of the Crestron website
(www.crestron.com). The name of the file is 5411i-cresnet.pdf.
Hookup Connections for the CNAMPX-16X60
MADE IN THE USA DATE:
LEFT
RIGHT
LEFT
1
2
1
2
3
4
3
4
RIGHT
U.S .A
CRESTRON
ELECTRONICS INC., ROCKLEIGH, N.J. 07670 USA
5
6
5
6
7
8
7
8
PWR
NET
24
NET
Y
Z
G
OVERRIDE
15A 125V
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE
HAZARD USE ONLY SAME TYPE AND RATING FUSE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
ATTENTION:
POUR LA PROTECTION CONTRE LES RISQUES D'INCENDIES
N'UTILISEZ SEULEMENT LE MÊMES TYPE DE FUSIBLE.
DÉBRANCHEZ LE CÂBLE D'ALIMENTATION AVANT DE
CHANGER LE FUSIBLE.
ACHTUNG:
AUFGRUND BRANDSCHUTZRECHTLICHER BESTIMMUNGEN,
BITTE NUR SICHERUNGEN DES SELBEN TYPS UND MIT DER
SELBEN BELASTBRAKEIT VERWENDEN. TRENNEN SIE DAS
GERAT VOM NETZ BEVOR SIE DIE SICHERUNG
AUSTAUSCHEN.
PRECAUCIÓN:
PARA LA PROTECCIÓN CONTINUADA CONTRA EL USO DEL
RIESGO DE INCENDIOS USE SOLAMENTE EL MISMO TIPO Y
FUSIBLE DEL GRADO. DESCONECTE LA CUERDA DE LA
FUENTE ANTES DE CAMBIAR EL FUSIBLE.
120V AC 60Hz
1800 WATTS MAX.
ROOM INPUTS
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
FROM CNX-PAD8
ROOM OUTPUTS
AUDIO TO
SPEAKERS
FROM AC OUTLET
OR POWER STRIP
TO CNX-PAD8
GROUND SCREW
TO CRESNET
CONTROL
SYSTEM
ROOM OUTPUTS
8 OHM / 60 WATTS
4 OHM / 90 WATTS
Identity Code
Every equipment and user interface within the Cresnet network requires a unique
NET ID. These codes are recognized by a two-digit hexadecimal number from 03 to
FE. The NET ID of the unit must match an ID code specified in the SIMPL
Windows program. The NET ID of the CNAMPX-16X60 is factory set to 3D. The
NET IDs of multiple CNAMPX-16X60 must all be unique and changed from a PC
via SIMPL Windows or Crestron VisionTools
Pro-e (VT Pro-e).
The method for changing the unit’s NET ID is identical regardless of the software
chosen. Attach one of the CNAMPX-16X60s to the control system (verify that the
software is running) and complete the following steps to change the NET ID:
1. Disconnect all Cresnet devices from the control system, except for the
unit that needs to have its NET ID changed.
2. Select
Tools | Viewport
to open the “Crestron Viewport” window.
3. Select
Functions | Set Network ID
. The software checks the baud rate
and then opens the “Set Network ID” window.
4. In the “Set Network ID” window, highlight the unit.
Operations Guide – DOC. 8155
16 Channel Professional Audio Amplifier: CNAMPX-16X60
•
9
