DO
GUIDE
DOC. 7833A (2045092) 10.15
Specifications subject to change without notice.
Power Pass-Through Outlet Connection
(TT-100 and TT-101 Only)
Connect the grounded ac power pass-through outlet and the power cord
(not shown) as required. The maximum load is 10 A @ 125 V, 50/60 Hz.
DO
Observe the Status Indicators
TT devices provide soft-touch capacitive Crestron Connect It™ buttons
with multicolored status indicators.
As of the date of manufacture, the TT-110 and TT-111 have been tested and found to comply with specifications for CE marking.
The TT-100 Series is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specific patents that cover Crestron products are listed at
http://www.crestron.com/legal/patents
.
The product warranty can be found at
www.crestron.com/warranty
.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource
.
Crestron, the Crestron logo, Cresnet, Crestron Connect It, and DigitalMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDMI and the HDMI Logo are either trademarks or registered trademarks of HDMI Licensing LLC in
the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron
is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
DO
Learn More
Visit the website for additional information and the latest firmware updates. To learn more about this product, use a QR reader application on
your mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
COLOR
DESCRIPTION
Blue
Video source is not connected.
Blinking Green
Video is detected. The display is turning on.
Solid Green
Video appears on the display.
Slowly Pulsating Green Video is detected; however, video does not
appear on the display.
Five Red Blinks
No video is detected. The Connect It button is
touched. After five red blinks, the color reverts to
blue.
Power
Pass-Through
Outlet
Crestron Connect It Buttons
