CSA-DECOR3 Series
Shade Motor and Hardware for CSA-DECOR3 Series Brackets
Product Information - 8675A
(2055416)
08.20
Getting Started
Scan the QR code to view the Quick Start Guide.
www.crestron.com/docs/7733
For additional information about the Crestron® CSA-DECOR3, visit
https://www.crestron.com/en-US/Products/Shades/Roller-Shade-
Systems/Hardware/CSS-DECOR3.
Certification and Compliance
The following Crestron® CSM-QMTDC series shade motors are
designed to operate with CSS-DECOR3 series shade mounting
hardware:
l
CSM-QMTDC-163-Y-EX
l
CSM-QMTDC-163-Y-CN
l
CSM-QMTDC-163-1-SG
l
CSMI-QMTDC-163-Y-EX
For proper installation, operation, and maintenance of these
products, refer to the corresponding Crestron manual located at
www.crestron.com/manuals.
Observe the following:
l
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
l
Children should be supervised to ensure that they do not play with
the appliance.
l
Use Crestron power supplies only.
l
The shade motor must only be supplied safety extra low voltage
(SELV) corresponding to the marking on the appliance.
l
When performing service or replacing parts, be sure to disconnect
the shade motor from its power source by removing the power
plug. Label the plug location with a note indicating its location
must be clearly visible while performing service.
l
Do not allow children to play with fixed controls. Keep remote
controls away from children.
l
Examine the installation frequently for imbalance and signs of
wear or damage to cables, springs and fixings. Do not use if repair
or adjustment is necessary.
l
Do not operate when maintenance, such as window cleaning, is
being carried out in the vicinity.
l
Disconnect the drive from the supply, or switch off the automatic
controls when maintenance, such as window cleaning, is being
carried out in the vicinity.
l
Do not use an extension cord. If the power supply cord is too
short, have a qualified electrician install an outlet near the drapery
operator.
l
The A-weighted emission sound pressure level of the drive is less
than 70 db(A).
WARNING: Important safety instructions. Follow all instructions
since incorrect installation can lead to severe injury.
l
The device should be installed using compatible mechanical parts
that are needed to couple the drive to the driven part.
NOTE: Mechanical parts are selected using the Crestron CDT
application. A list of parts are also available on the Crestron
website at www.crestron.com.
l
Before installing the drive, remove any unnecessary cords or
components and disable any equipment not needed for powered
operation.
l
Install the actuating member of any manual release at a height
less than 5.91 ft (1.8 m).
l
The motor is intended to be installed at a height of at least 8.2 ft
(2.5 m) above floor level or other access level.
For motors supplied without a driven part:
l
The motor must be used with compatible parts at the rated load
and operating time.
l
The motor must be used with the correct diameter roller tube or
the correct drapery track.
l
Follow installation instructions supplied with the mounting
brackets, motor, roller tube, and drapery track.
The following symbols are used on the product:
l
Direct Current:
l
Class III Appliance:
For Bracket Model: CSA-DECOR3
As of the date of manufacture, the product has been tested and
found to comply with specifications for CE marking.
For Motor Models: CSM-QMTDC-163-Y-EX, CSMI-QMTDC-163-Y-EX
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful
communication.
Industrie Canada (IC) Déclaration de conformité
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement. Conformément à
la réglementation d’Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou
inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à l’intention
des autres utilisateurs, il faut choisir le type d’antenne et son gain de
sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
