Change the Blade Insert (CSAI-PWS40 Only)
1.
If a blade insert is attached to the CSAI-PWS40, slide the spring-loaded locking key
downward and then pull upward on the blade insert to remove it.
2.
Insert the top edge of the blade assembly into the top of the CSAI-PWS40 at
a 30-60 degree angle.
NOTE:
The top edge of the blade assembly is flat, and the bottom edge is U-shaped.
The CSAI-PWS40 is shaped similarly.
3.
Push the blade insert down into the CSAI-PWS40 until it locks into place. A clicking
sound will occur.
4.
Pull up on the blade to check that the blade insert is securely installed.
Technical Specifications
Refer to the CSA-PWS40 product page at
for a complete list of product
specifications.
Specification
Details
Output Rating
24 VDC, 40 W (1.66 A), regulated
Power Requirements
1 A @ 100-240 VAC, 50/60 Hz
Connections
Line
Load
(1) power plug, line power input
(1) 8 ft (2.43 m) attached cable with inline ferrite core and
flying leads
Construction
94V-0 polycarbonate, white, outlet-mountable
Environmental
Temperature
Humidity
32º to 104ºF (0º to 40ºC)
15% to 95% RH (noncondensing)
Weight
6.4 oz (182 g)
Additional Information
Scan or click the QR code for detailed product information.
CSAI-PWS40
Compliance and Legal
Original Instructions:
The U.S. English version of this document is the original instructions. All other languages are a
translation of the original instructions.
As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.
This product is listed to applicable UL® Standards and requirements tested by Intertek® services.
Ce produit est homologué selon les normes et les exigences UL applicables par Intertek Prestations de service.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may
not cause harmful interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void
the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents
.
Certain Crestron products contain open source software. For specific information, please visit
Crestron, the Crestron logo, and infiNET EX are either trademarks or registered trademarks of Crestron Electronics, Inc.
in the United States and/or other countries. The ETL logo is either a trademark or registered trademark of Intertek Testing
Services NA in the United States and/or other countries. UL is either a trademark or registered trademark of Underwriters
Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names
may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron
disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
Quick Start - Doc. 7370D
(2053450)
05/15/19
Specifications subject to
change without notice.
