The Crestron® HD-RX-4K-510-C-E is a DM Lite™ 4K multiformat switch and receiver that
provides enhanced HDMI® video switching and audio presentation capabilities in areas such as
conference rooms and classrooms. The HD-RX-4K-510-C-E can be connected to up to three
DM Lite transmitters.
Check the Box
Item
Qty
HD-RX-4K-510-C-E
1
Anchor, Drywall, Plastic (P/N 2053825)
4
Connector, 2-Pin (P/N 2003574)
5
Connector, 2-Pin (P/N 2044402)
2
Connector, 3-Pin (P/N 2003575)
3
Connector, 5-Pin (P/N 2003577)
5
Power Cord, 6 ft 7 in. (2 m) (P/N 2001134)
1
Screw, 8-15A x 3/4 in., Flat Head, Phillips (P/N 2053836)
4
Install the Device
To install the device, mount it onto drywall. Use the four included drywall anchors and the four
included 8-15A x 3/4 in. flat head Phillips screws (one screw for each keyhole slot in the four
mounting flanges of the device).
NOTE:
For safety reasons, it is recommended that the mounting height of the device be no more
than 6-1/2 ft (2 m) from the floor or any platform above which the device is mounted.
Drywall Mounting
(4) Screws, 8-15A x 3/4 in.
(included)
Drywall
HD-RX-4K-510-C-E
(4) Mounting flange
keyhole slots
(2 each side)
(4) Anchors
(included)
Connect the Device
Connect the device as required for the application.
Front Panel Connection
SERVICE:
For firmware
and EDID
loading
PWR
LED
INPUT Selection
1-5
LEDs and
push buttons
AUTO
LED and
push button
SETUP
LED and
push button
Rear Panel Connections
DM LITE
INPUTS 5, 4, 3:
From
DM Lite™
transmitters
HDMI
INPUTS 2, 1:
From HDMI®
audio/video
sources
HDMI
OUTPUT:
To HDMI
display
:
100BASE-TX/
1000BASE-T
Ethernet to
local area network
IR:
To IR
controllable
device
COM:
To RS-232
device
SPEAKER L/R OUT:
To 4-ohm or
8-ohm
stereo speakers
100-240V~2.0A
50/60 Hz:
From AC
power outlet
I/O 1-2:
To I/O
controllable
devices
RLY 1-2:
To contact
closure
devices
LINE L/R 1-2 :
From balanced/
unbalanced stereo line
level audio sources
MIC 1-2:
From balanced
microphone
audio sources
AUX:
From balanced
auxiliary
audio source
AUX OUT 1-2:
To balanced/
unbalanced
auxiliary
audio devices
NOTES:
•
Cabling that connects the HD-RX-4K-510-C-E to a DM Lite transmitter is designed for
intrabuilding use only.
•
The HD-RX-4K-510-C-E can power three DM Lite transmitters simultaneously. Do not
connect power to transmitters that are to be connected to the HD-RX-4K-510-C-E.
•
The HD-RX-4K-510-C-E is grounded by connection of the included power cord to an
AC power outlet with proper grounding.
•
There are no user-serviceable parts inside this device. If repair of the device is needed,
contact an authorized Crestron dealer for return of the device to the factory.
LINE 1-2 Connector Pin Assignments
The LINE 1 and LINE 2 connectors use 5-pin terminal blocks for balanced or unbalanced analog
audio inputs.
LINE 1-2 Connector
+
+ –
–
Refer to the following table and diagrams for analog audio input pin assignments and
connection information.
Signal Name Balanced Audio Input Unbalanced Audio Input
+
L+
L+ In
–
L–
L– signal return, jumper to GND
G
Shield/ground
Ground
+
R+
R+ In
–
R–
R– signal return, jumper to GND
Jumpers
+ - G + -
+
+
L R
Source L
Source R
Shield
Shield
+ - G + -
+
+
Shield
L R
Source L
Source R
Unbalanced Input
Balanced Input
AUX OUT 1-2 Connector Pin Assignments
The AUX OUT 1 and AUX OUT 2 connectors use 5-pin terminal blocks for balanced or unbalanced
analog audio outputs.
AUX OUT 1-2 Connector
+
+ –
–
Refer to the following table and diagrams for analog audio output pin assignments and
connection information.
Signal Name
Balanced Audio Output Unbalanced Audio Output
+
L+
L+ Out
–
L–
Open
G
Shield/ground
Common ground
+
R+
R+ Out
–
R–
Open
AMP
Left
Right
+ - G + -
Unbalanced Output
L R
+
+
Shield
AMP
Left
Right
+ - G + -
Balanced Output
L R
+
+
HD-RX-4K-510-C-E
DM Lite™ 4K Multiformat Switch and Receiver
