DO
GUIDE
DO
Install the Device
The DM-TX-4K-100-C-1G can be mounted into an electrical box, under a table, or onto a flat
surface or rack rail.
Mounting into an Electrical Box
The DM-TX-4K-100-C-1G mounts into a 1-gang electrical box (not included). A minimum
mounting depth of 3-1/2 inches (89 mm) is required.
Using a Phillips head screwdriver, attach the DM-TX-4K-100-C-1G to the electrical box using
the two included 6-32 x 3/4-inch truss combo head screws. Then, attach a decorator-style
faceplate (not included) to the front panel of the DM-TX-4K-100-C-1G using two screws (not
included). Refer to illustration
.
Mounting into an Electrical Box
DM-TX-4K-100-C-1G
Wall Plate 4K DigitalMedia 8G+
®
Transmitter 100
DO
Make Connections to the Rear Panel
Make connections to the rear panel of the Crestron
®
DM-TX-4K-100-C-1G before mounting the
unit into an electrical box. If the unit is to be mounted under a table or onto a flat surface or rack
rail, make connections to the rear panel after the unit is mounted. (For mounting instructions,
refer to the “DO Install the Device” section in this guide.)
Make connections to the rear panel as follows:
DM OUT:
Connect to the DM 8G+
®
input of a DigitalMedia™ switcher, DigitalMedia 8G+
®
receiver, or other DigitalMedia device or to an HDBaseT
®
device.
NOTE:
The DM OUT port is a PoDM (Power over DM) and HDBaseT
®
PoE (Power over Ethernet)
PD (Powered Device) port. To receive PoDM or HDBaseT PoE, the DM-TX-4K-100-C-1G requires
a connection to a DigitalMedia switcher or other equipment that has a PoDM or HDBaseT PoE
PSE (Power Sourcing Equipment) port. Any wiring that is connected to a PoDM or HDBaseT PoE
PSE port is for intrabuilding use only and should not be connected to a line that runs outside of
the building in which the PSE is located.
24VDC 0.75A:
Connect to the included power pack using the included 2-pin interface
connector.
NOTE:
Connection to the power pack is not required when PoDM or HDBaseT PoE is used to
power the device.
G:
Connect to earth ground (building steel).
Refer to illustrations
and
for sample rear panel connections.
Connection to DigitalMedia Switcher Using PoDM
(External Power Pack Not Required)
DO
Check the Box
QTY PRODUCT
COLOR
PART NUM.
1
Bracket (for Interface Module)
Black
2016054
2
Connector, 2-Pin
2003574
1
Connector, 3-Pin
2003575
1
Power Pack, 24 Vdc 0.75 A, 100-240 Vac
2045866
2
Screw, 6-32 x 3/4", Truss Head, Combo
2009211
2
Screw, 6-32 x 1/4", Pan Head, SEMS
Black
2007218
DM-RMC-4K-100-C
Ground
D M
- R M
C - 4
K - 1
0 0 -
C
DM
RO
OM
CO
NTR
OLL
ER
DBT
ASE
TM
HDM
I OU
T
GND
TX
RX
RTS
CTS
COM
S
G
S
G
1
2
IR
LAN
DM
IN
RES
ET
SET
UP
24 V
0.75
A M
AX
Power
pack
Connection to DigitalMedia Receiver
(External Power Pack Required)
DM-MD8X8
Ground
