background image

 

8  

  DMF-CI-8: DM NVX and DMCF Card Chassis 

Supplemental Guide – DOC. 7861C 

NOTE: 

If the Lock parameter, which is located below the Mode parameter, is set 

to Unlocked, continue with step 2. The Unlocked setting allows the Mode setting 

to be changed. 

If the Lock parameter is set to Locked, the Mode setting cannot be changed.  

To unlock the Mode parameter, use the DM NVX web interface. The device  

mode can then be changed using the DM NVX web interface or the DMF-CI-8 

front panel.  

2.

 

For the Mode parameter, select Receiver or Transmitter. The default setting  

is Receiver. 

A screen appears on the display, allowing the device mode to be changed for the 

selected card. 

Change Device Mode Screen 

                                                

Card      2 

Name: DM-NVX-350C-00 

 

 

                Apply              

 

 

                    Exit 

3.

 

Select Apply to change the device mode. (Selecting Exit prevents the device  

mode from being changed.)  

The card reboots. When the reboot process is complete, the corresponding  

TX 1–8 or RX 1–8 LED on the front panel lights green to indicate that the card is 

in transmitter (TX) or receiver (RX) mode.  

View and Configure Input Routing Settings 

NOTE: 

Input routing status and configuration are applicable to the DM-NVX-350C and  

DM-NVX-351C cards only. 

To view and configure input routing settings: 

On the card status and configuration menu, select Input Routing. 

Card Status and Configuration Menu 

_ DM-NVX-350C-00107_ 

            Device Mode         

        Input Routing       

 

        Network Settings 

             Diagnostics 

 

 

      

The Status and Input Routing menu appears on the display for the selected card.  

Summary of Contents for DMF-CI-8































Reviews: