background image

 

Supplemental Guide – DOC. 7861C 

DMF-CI-8: DM NVX and DMCF Card Chassis  

  21 

View Chassis Details 

Chassis details consist of the serial number and firmware version of the chassis. To view 

chassis details: 

On the Chassis menu, select Details. 

Chassis Menu 

                Chassis                 

             Details             

 

                Status     

       Front Panel State 

       Firmware Update 

               Restore 

 

 

The Details screen appears on the display showing the serial number and firmware 

version of the chassis.  

Sample Chassis Details Screen 

                Details              

a

 

Serial Number: 

00F626E9 

 

Firmware Version: 

1.3054.60 

           

                

View Chassis Status 

Chassis status consists of the operating temperature and the RPM of each fan in the 

chassis. To view the chassis status: 

On the Chassis menu, select Status. 

Chassis Menu 

                Chassis                 

                Details             

            Status               

 

       Front Panel State 

       Firmware Update 

                Restore 

 

 

The Status screen appears on the display showing the operating temperature of the 

chassis and the RPM of each fan in the chassis. A sample screen is shown on the 

following page. 

 

Summary of Contents for DMF-CI-8































Reviews: